Edelbrock 3564 User Manual
Page 2
MANIFOLD ASSEMBLY CONTENTS
Catalog #3562, 3563, 3564, 3565
Rev. 3/06
Page 2 of 16
©2006 Edelbrock Corporation
Brochure #63-0047
Qty.
Description
❑
1
Manifold assembly (see detail below)
❑
1
Installation instructions
❑
1
EPROM adapter circuit board (#3562 only)
❑
1
Fuel injector wiring harness
❑
1
Fuel filter adapter fitting (filter to #6 AN male) with O-ring
❑
1
Return line adapter fitting
❑
2
#6 AN straight pushlock fittings
❑
1
3/8" i.d. pushlock heat resistant fuel line, 10 foot length
❑
1
#6 AN 45 degree elbow pushlock fitting
❑
1
#6 AN 90 degree elbow pushlock fitting
❑
1
Fuel line clamp (floor mounted)
❑
4
11" tie wrap
❑
1
Throttle cable bracket
❑
1
Throttle body block-off plate
❑
1
Throttle body gasket
❑
1
EGR gasket
❑
1
3/8" NPT pipe plug
❑
1
3/8” I.D. Flatwasher
Qty.
Description
❑
1
3/8" NPT male to 3/8” NPT female 90 Degree elbow
❑
1
3/8" NPT to 1/2” hose brass fitting
❑
1
2 foot length 15/32 i.d vacuum line (power brakes)
❑
1
6” length 3/8’ fuel line (breather line extension)
❑
1
1/2" NPT to 3/4" hose barb
❑
1
36" length 3/4" i.d. heater hose
❑
1
3" length 5/16" i.d. high pressure fuel line (pump to sending
unit)
❑
1
2 foot length 5/32" i.d. vacuum line (regulator & EGR)
❑
1
5-1/8" i.d. air cleaner base gasket
❑
1
12" length 1/4" i.d. vacuum line (MAP)
❑
1
1/2”
hose
clamps
❑
2
3/4" hose clamp
❑
1
3/8" hose clamp (fuel injection clamp)
❑
1
5/16" hose clamp (fuel injection clamp)
❑
1
1/4" x 1/4" out x 5/32" bottom out vacuum “T” fitting
❑
1
10-16 x 3/4" TEX screw (self tapping)
❑
1
Air Cleaner Lid decal
PERFORMER MULTI-POINT EFI
KIT CONTENTS
Qty.
Description
❑
1 Intake manifold
❑
1 Driver’s side (left side) fuel rail
❑
1 Passenger’s side (right side) fuel rail
❑
4 1/4"-20 x 1.25" Hex head cap screw rail hold down bolts
❑
1 Fuel pressure regulator
❑
8 Magnetti Marelli
®
pico injectors
❑
1 Fuel crossover line (including adapter and schrader valve)
❑
1 Fuel inlet fitting (3/8" male pipe to #6 AN male, steel)
Qty.
Description
❑
1 Fuel regulator nut and Viton O-ring
❑
1 Viton O-ring; fuel regular nut (1/2" o.d. 5/16" i.d.)
❑
4 1/4" i.d. AN thin flat washers
❑
1 1/4"-20 x 1/2" hex head cap screw
❑
1 1/4" i.d. split lock washer
❑
1 Schrader valve cap
❑
4 1/4" internal star lock washers
SUGGESTED TOOLS AND MATERIALS FOR INSTALLATION
❑
3/8" ratchet socket set with extensions
❑
Combination set of open-end wrenches (SAE and metric)
❑
Jackstands, screwdrivers, pliers, crescent wrench, hacksaw,
hammer, brass punch and assorted hand tools
❑
Torx screwdrivers
❑
Tin snips
❑
White grease
❑
Teflon thread sealant or equivalent
❑
Intake gasket set (Edelbrock #7205, GM #10181398, or
equivalent)
❑
Thermostat housing gasket (GM #10105135, Fel-Pro #2201, or
equivalent)
❑
Gasket sealant (Gasgacinch, etc.)
❑
RTV Silicone sealant; O
2
sensor-safe
❑
Wire stripper & crimper
❑
Heat gun or lighter