Sealey TA070 User Manual

Page 2

Advertising
background image

NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.

IMPORTANT: No liability is accepted for incorrect use of this product.

WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.

INFORMATION: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.

01284 757500

01284 703534

[email protected]

Sole UK Distributor, Sealey Group,

Kempson Way, Suffolk Business Park

,

Bury St. Edmunds, Suffolk,

IP32 7AR

www.sealey.co.uk

Web

email

Original Language Version

TA070 Issue: 1 - 03/07/12

© Jack Sealey Limited 2012

3.2.2. Press the SET button (fig.1.2) to scroll down to the

desired unit of measurement on the display screen

(fig.2).

3.2.3. Once the desired unit of measurement for air velocity

has been selected, press the MODE button (fig.1.1) to

confirm the selection.

3.3. Selecting the Air Velocity measuring mode

3.3.1. The unit has 3 modes for the measurement of air

velocity:

a. CU - Current Air Velocity.

b. MAX - Maximum Air Velocity Measured.

c. AVG - Average Air Velocity Measured.

3.3.2. To select the desired measuring mode, with the unit

switched on, hold down the MODE button (fig.1.1) for

3 seconds until the 'm/s' symbol on the display screen

(fig.2) starts to flash.

3.3.3. Press the SET button (fig 1.2) and scroll through the

units of measurement until 'CU' is displayed in the

temperature display area on the screen (fig.2). Continue

to press the SET button (fig.1.2) to scroll to 'MAX or

'AVG' measuring mode, as indicated on the display.

3.3.4. Once the desired measuring mode has been selected,

press the MODE button (fig.1.1) to confirm the selection.

Note: The settings will remain stored when the unit is

switched off normally. If the battery is removed, the unit

will default to the factory presets.

3.4. Setting the Unit of Measurement (Temperature)

3.4.1. Remove the unit from the protective shroud (fig1.6).

3.4.2. Switch the unit on, and insert a suitable pin into the

temperature setting apeture at the rear of the unit

(fig.1.3). Press the internal switch to change the

temperature unit of measurement between °C and °F.

3.5. Digital Display Backlight

3.5.1. When the unit is switched on, press any button to

illuminate the display backlight for a 12 second period.

3.6. Digital Display (fig.2)

3.6.1. With the unit switched on and the impeller (fig.1.4)

rotating, the wind speed, temperature and Beaufort

Scale readings will show on the display screen.

3.6.2. If the temperature falls below 0°C (32°F) the 'wind chill'

function will activate and show on the display (fig.2).

3.7. Switch Off Procedure

3.7.1. To switch the unit off, press the MODE button (Fig.1.1)

and the SET button (fig.1.2) simultaneously.

3.7.2. If the unit is switched on and not used for more than 14

minutes, the 'auto power shut off' function will switch off

the unit.

3.8. Battery Replacement

3.8.1. If the Battery Condition Indicator (fig.2) displays the

symbol, the battery requires replacement.

3.8.2. Remove the unit from the protective shroud (fig.1.6).

3.8.3. Using a coin, rotate the battery cover (fig.1.5) counter-

clockwise until it can be removed from the unit. Remove

the unserviceable battery and replace with a

serviceable CR2032 3V battery. Re-fit the battery

cover (fig.1.5) and rotate clockwise until locked into

place.

3.8.4. Re-fit the protective shroud (fig.1.6).

Environmental Protection

Recycle unwanted materials insread of disposing of them as waste.

All tools, accessories and packaging should be sorted, taken to a recycle centre and disposed of in a manner which is

compatible with the environment.

When a product is no longer required, it must be disposed of in an environmentally protective way. Contact your

local solid waste authority for recycling information.

Battery Removal

Open the rear cover as in Section 3.8.

Remove the battery.

Replace the cover.

Dispose of batteries according to local authority guidelines.

Under the Waste Batteries and Accumulators Regulations 2009, Jack Sealey Ltd are required to inform potential

purchasers of products containing batteries (as defined within these regulations), that they are registered with Valpak's

registered compliance scheme. Jack Sealey Ltd's Batteries Producer Registration Number (BPRN) is BPRN00705.

4. SPECIFICATION

Advertising