Whelen 508TRIM - Manual

Page 1
DOUBLE-SIDED
TAPE
Peel off one side of tape backing and apply to
the 4 sides of the back of the trim ring as shown.
(The longer pieces will go on the top and bottom.)
REAR VIEW OF TRIM RING
DOUBLE-SIDED
TAPE
Peel off one side of tape backing and apply to
the 4 sides of the back of the trim ring as shown.
(The longer pieces will go on the top and bottom.)
REAR VIEW OF TRIM RING
51 Winthrop Road,
Chester, Connecticut 06412-0684
Phone: (860) 526-9504
Fax: (860) 526-4078
51 Winthrop Road,
Chester, Connecticut 06412-0684
Phone: (860) 526-9504
Fax: (860) 526-4078
MOD EL 81 0 SE RIE S
WHE LEN ENG . CO . PAT . PEN D.
MOD EL 5 08 S ERIE S
MOD EL 5 08 S ERIE S
WHE LEN EN G. C O.
WHELEN ENG . CO . PAT . PEN D. PAT . PEN D.
PAT . PEN D.
WHELEN
ENG . CO.
MOD EL 5 08 S ERIE S
MOD EL 8 10 S ERIE S
WHE LEN ENG . CO . PAT . PEN D.
MOD EL 8 10 SER IES
WHE LEN ENG . CO . PAT . PEN D.
810 SERIES DUAL HALOGEN
508 SERIES DUAL HALOGEN 508 SERIES SCENELIGHT 508 SERIES LINEAR STROBE
810 SERIES SCENELIGHT 810 SERIES LINEAR STROBE
©2000 Whelen Engineering Company Inc.
Form No.13888A (062807)
Automotive:
Li
ghtheads
Installation Guide:
508 / 810 Series Flange Cover
®
ENGINEERING COMPANY INC.
Internet: www.whelen.com
Sales e-mail: [email protected]
Canadian Sales e-mail: [email protected]
Customer Service e-mail: [email protected]
©2000 Whelen Engineering Company Inc.
Form No.13888A (062807)
Automot
ive:
Li
ghtheads
Installation Guide:
508 / 810 Series Flange Cover
®
ENGINEERING COMPANY INC.
Internet: www.whelen.com
Sales e-mail: [email protected]
Canadian Sales e-mail: [email protected]
Customer Service e-mail: [email protected]
Mounting:
First clean all mounting surfaces with isopropyl alcohol. Remove the protective backing to expose one side of the double stick tape (supplied).
Apply a length of the tape toeach of the 4 sides of the existing flange as shown below.
WARNING: After Installation, the outer surfaces of this
product may be cleaned with mild soap and water. The
use of any other chemicals may void product warranty.
Do not use a pressure washer.
MOD EL 8 10 S ERIE S
WHE LEN ENG . CO . PAT . PEN D.
MOD EL 5 08 S ERIE S
MOD EL 5 08 S ERIE S
WHELEN EN G. C O.
WHELEN ENG . CO . PAT . PEN D. PAT . PEN D. PAT . PEN D.
WH ELEN ENG . CO.
MOD EL 5 08 S ERIE S
MOD EL 8 10 S ERIE S
WHE LEN ENG . CO . PAT . PEN D.
MOD EL 8 10 S ERIE S
WHE LEN ENG . CO . PAT . PEN D.
810 SERIES DUAL HALOGEN
508 SERIES DUAL HALOGEN 508 SERIES SCENELIGHT 508 SERIES LINEAR STROBE
810 SERIES SCENELIGHT 810 SERIES LINEAR STROBE
Mounting:
First clean all mounting surfaces with isopropyl alcohol. Remove the protective backing to expose one side of the double stick tape (supplied).
Apply a length of the tape toeach of the 4 sides of the existing flange as shown below.
WARNING: After Installation, the outer surfaces of this
product may be cleaned with mild soap and water. The
use of any other chemicals may void product warranty.
Do not use a pressure washer.
For warranty information regarding this product, visit www.whelen.com/warranty
For warranty information regarding this product, visit www.whelen.com/warranty