Whelen L6BKT2 - Manual

Page 1
8 X 3/8 PPHSMS (Bracket to Vehicle) (QTY 3)
SAE
W-1
80
SAE
W-1
80
S AE
W
-1
80
S AE
W
-1
80
L6BKT2
DODGE CHARGER
6-32 X 3/8
P P H M S
(QTY 2)
©2009 Whelen Engineering Company Inc.
Form No.14301 (051309)
Automotive:
Li
ghtheads
Installation Guide:
LINZ6™ Mounting Bracket Model L6BKT2
2007-2009 Dodge Charger Trunk Lid
®
ENGINEERING COMPANY INC.
Internet: www.whelen.com
Sales e-mail: [email protected]
Canadian Sales e-mail: [email protected]
Customer Service e-mail: [email protected]
For warranty information regarding this product, visit www.whelen.com/warranty
51 Winthrop Road,
Chester, Connecticut 06412-0684
Phone: (860) 526-9504
Fax: (860) 526-4078
Installation and Wiring:
1. Secure the lighthead (with gasket) to the mounting bracket.
2. Locate mounting area (Fig. 1). Using the bracket as a template,
mark the 3 mounting hole locations onto the mounting surface
(Fig. 2). Use the existing hole in the trunk for the wire hole.
3. Drill three, .144” diameter mounting holes (#27 drill bit) into the
mounting surface (in the locations marked off in step 2) and
secure the bracket with the 3 supplied 8 X 3/8” PPHSM screws.
4. Extend the lighthead wires to their connections and refer to the
lighthead manual for fusing and operation.
IMPORTANT! It is the responsibility of the installation technician to
make sure that the installation and operation of this product will not
interfere with or compromise the operation or efficiency of any vehicle
equipment!
IMPORTANT! Before returning the vehicle to active service, visually
confirm the proper operation of this product, as well as all vehicle
components/equipment
Fig. 1 Fig. 2
Mount Here
8 X 3/8 PPHSMS (Bracket to Vehicle) (QTY 3)
SAE
W-1
80
SAE
W-1
80
S AE
W
-1
80
S AE
W
-1
80
L6BKT2
DODGE CHARGER
6-32 X 3/8
P P H M S
(QTY 2)
©2009 Whelen Engineering Company Inc.
Form No.14301 (051309)
Automot
ive:
Li
ghtheads
Installation Guide:
LINZ6™ Mounting Bracket Model L6BKT2
2007-2009 Dodge Charger Trunk Lid
®
ENGINEERING COMPANY INC.
Internet: www.whelen.com
Sales e-mail: [email protected]
Canadian Sales e-mail: [email protected]
Customer Service e-mail: [email protected]
For warranty information regarding this product, visit www.whelen.com/warranty
51 Winthrop Road,
Chester, Connecticut 06412-0684
Phone: (860) 526-9504
Fax: (860) 526-4078
Installation and Wiring:
1. Secure the lighthead (with gasket) to the mounting bracket.
2. Locate mounting area (Fig. 1). Using the bracket as a template,
mark the 3 mounting hole locations onto the mounting surface
(Fig. 2). Use the existing hole in the trunk for the wire hole.
3. Drill three, .144” diameter mounting holes (#27 drill bit) into the
mounting surface (in the locations marked off in step 2) and
secure the bracket with the 3 supplied 8 X 3/8” PPHSM screws.
4. Extend the lighthead wires to their connections and refer to the
lighthead manual for fusing and operation.
IMPORTANT! It is the responsibility of the installation technician to
make sure that the installation and operation of this product will not
interfere with or compromise the operation or efficiency of any vehicle
equipment!
IMPORTANT! Before returning the vehicle to active service, visually
confirm the proper operation of this product, as well as all vehicle
components/equipment
Fig. 1 Fig. 2
Mount Here