Whelen L6BKT3 - Manual

Page 1
©2009 Whelen Engineering Company Inc.
Form No.14299 (051209)
Automotive:
Li
ghtheads
Installation Guide:
LINZ6™ Mounting Bracket Model L6BKT3
for Police Push-Bumper
®
ENGINEERING COMPANY INC.
Internet: www.whelen.com
Sales e-mail: [email protected]
Canadian Sales e-mail: [email protected]
Customer Service e-mail: [email protected]
For warranty information regarding this product, visit www.whelen.com/warranty
51 Winthrop Road,
Chester, Connecticut 06412-0684
Phone: (860) 526-9504
Fax: (860) 526-4078
Installation and Wiring:
1. Secure the lighthead (with
gasket) to the mounting
bracket.
2. Using the bracket as a
template, mark the 2
mounting hole locations onto
the mounting surface.
3. Drill two 9/32” diameter
mounting holes into the
mounting surface (in the
locations marked off in step
2) and secure the bracket
with the supplied 1/4 - 20 X
3/4” Hex Head Metal Screws.
4. Extend the lighthead wires to
their connections and refer to the lighthead manual for fusing
and operation.
IMPORTANT! It is the responsibility of the installation technician to
make sure that the installation and operation of this product will not
interfere with or compromise the operation or efficiency of any
vehicle equipment!
IMPORTANT! Before returning the vehicle to active service, visually
confirm the proper operation of this product, as well as all vehicle
components/equipment
L6BKT3
46° Push-Bumper
Bracket
1/4 - 20 x 3/4"
HEX HEAD
METAL SCREW
(QTY 2)
1/4 - 20 ELASTIC
STOP NUT (QTY 2)
PUSH-BU
MPER
6 - 32 X 3/4
PPHMS
(QTY 2)
GASKET
(QTY 1)
LINZ6™
(not
included)
BRACKET
(QTY 1)
6 - 32 X 5/16 ELASTIC
STOP NUT (QTY 2)
©2009 Whelen Engineering Company Inc.
Form No.14299 (051209)
Automot
ive:
Li
ghtheads
Installation Guide:
LINZ6™ Mounting Bracket Model L6BKT3
for Police Push-Bumper
®
ENGINEERING COMPANY INC.
Internet: www.whelen.com
Sales e-mail: [email protected]
Canadian Sales e-mail: [email protected]
Customer Service e-mail: [email protected]
For warranty information regarding this product, visit www.whelen.com/warranty
51 Winthrop Road,
Chester, Connecticut 06412-0684
Phone: (860) 526-9504
Fax: (860) 526-4078
Installation and Wiring:
1. Secure the lighthead (with
gasket) to the mounting
bracket.
2. Using the bracket as a
template, mark the 2
mounting hole locations onto
the mounting surface.
3. Drill two 9/32” diameter
mounting holes into the
mounting surface (in the
locations marked off in step
2) and secure the bracket
with the supplied 1/4 - 20 X
3/4” Hex Head Metal Screws.
4. Extend the lighthead wires to
their connections and refer to the lighthead manual for fusing
and operation.
IMPORTANT! It is the responsibility of the installation technician to
make sure that the installation and operation of this product will not
interfere with or compromise the operation or efficiency of any
vehicle equipment!
IMPORTANT! Before returning the vehicle to active service, visually
confirm the proper operation of this product, as well as all vehicle
components/equipment
L6BKT3
46° Push-Bumper
Bracket
1/4 - 20 x 3/4"
HEX HEAD
METAL SCREW
(QTY 2)
1/4 - 20 ELASTIC
STOP NUT (QTY 2)
PUSH-B
UMPER
6 - 32 X 3/4
PPHMS
(QTY 2)
GASKET
(QTY 1)
LINZ6™
(not
included)
BRACKET
(QTY 1)
6 - 32 X 5/16 ELASTIC
STOP NUT (QTY 2)