Whelen REPS30WD - Manual

IMPORTANT WARNING FOR
SYSTEMS FEATURING STROBE
LAMP HOLDER ASSEMBLIES!!!
THE STROBE LIGHT POWER SUPPLY IS A HIGH VOLT-
AGE DEVICE. DO NOT REMOVE STROBE LAMP
HOLDER ASSEMBLY OR DISMANTLE STROBE LIGHT
HEAD ASSEMBLY WHILE SYSTEM IS IN OPERATION.
WAIT 10 MINUTES AFTER TURNING OFF POWER
BEFORE STARTING ANY WORK OR TROUBLE
SHOOTING OF THE SYSTEM.
© Whelen Engineering Company Inc.
Form No. 13339A (062598)
LAMP
REPLACEMENT . . .
TO AVOID PERSONAL INJURY,
ATTEMPT TO REPLACE THE LAMP WITH FINGERS...
USE THE LAMP REPLACEMENT TOOL INCLUDED IN KIT.
The lamp assembly is packed with the lamp replacement tool
protecting the glass tube.
In some cases, the reflector may have to be removed for
lamp replacement. If the lamp does not easily exit reflector,
remove the reflector and check for obstructions.
Make sure gasket on lamp assembly is in place. Route the
wire assembly through the reflector, and follow procedures
as outlined in steps 6 and 7 on the other side of this page in
lamp replacement instruction text.
WARNING!
1.
2.
DO NOT
51 WINTHROP ROAD
CHESTER, CONNECTICUT 06412-0684
TELEPHONE: (860) 526-9504
FAX: (860) 526-4078
IMPORTANT WARNING FOR
SYSTEMS FEATURING STROBE
LAMP HOLDER ASSEMBLIES!!!
THE STROBE LIGHT POWER SUPPLY IS A HIGH VOLT-
AGE DEVICE. DO NOT REMOVE STROBE LAMP
HOLDER ASSEMBLY OR DISMANTLE STROBE LIGHT
HEAD ASSEMBLY WHILE SYSTEM IS IN OPERATION.
WAIT 10 MINUTES AFTER TURNING OFF POWER
BEFORE STARTING ANY WORK OR TROUBLE
SHOOTING OF THE SYSTEM.
© Whelen Engineering Company Inc.
Form No. 13339A (062598)
LAMP
REPLACEMENT . . .
TO AVOID PERSONAL INJURY,
ATTEMPT TO REPLACE THE LAMP WITH FINGERS...
USE THE LAMP REPLACEMENT TOOL INCLUDED IN KIT.
The lamp assembly is packed with the lamp replacement tool
protecting the glass tube.
Make sure gasket on lamp assembly is in place. Route the
wire assembly through the reflector, and follow procedures
as outlined in steps 6 and 7 on the other side of this page in
lamp replacement instruction text.
WARNING!
2.
DO NOT
1. In some cases, the reflector may have to be removed for
lamp replacement. If the lamp does not easily exit reflector,
remove the reflector and check for obstructions.
51 WINTHROP ROAD
ROUTE 145, WINTHROP ROAD
CHESTER, CONNECTICUT 06412-0684
TELEPHONE: (860) 526-9504
FAX: (860) 526-4078
IMPORTANT WARNING FOR
SYSTEMS FEATURING STROBE
LAMP HOLDER ASSEMBLIES!!!
THE STROBE LIGHT POWER SUPPLY IS A HIGH VOLT-
AGE DEVICE. DO NOT REMOVE STROBE LAMP
HOLDER ASSEMBLY OR DISMANTLE STROBE LIGHT
HEAD ASSEMBLY WHILE SYSTEM IS IN OPERATION.
WAIT 10 MINUTES AFTER TURNING OFF POWER
BEFORE STARTING WORK OR TROUBLE
SHOOTING OF THE SYSTEM.
ANY
© Whelen Engineering Company Inc.
Form No. 13339A (062598)
LAMP
REPLACEMENT . . .
TO AVOID PERSONAL INJURY,
ATTEMPT TO REPLACE THE LAMP WITH FINGERS...
USE THE LAMP REPLACEMENT TOOL INCLUDED IN KIT.
The lamp assembly is packed with the lamp replacement tool
protecting the glass tube.
Make sure gasket on lamp assembly is in place. Route the
wire assembly through the reflector, and follow procedures
as outlined in steps 6 and 7 on the other side of this page in
lamp replacement instruction text.
WARNING!
2.
DO NOT
1. In some cases, the reflector may have to be removed for
lamp replacement. If the lamp does not easily exit reflector,
remove the reflector and check for obstructions.
51 WINTHROP ROAD
CHESTER, CONNECTICUT 06412-0684
TELEPHONE: (860) 526-9504
FAX: (860) 526-4078
®
PIONEERS IN SAFETY SIGNALS
ENGINEERING COMPANY, INC.
®
PIONEERS IN SAFETY SIGNALS
ENGINEERING COMPANY, INC.
®
PIONEERS IN SAFETY SIGNALS
ENGINEERING COMPANY, INC.
GASKET
FIT WINGS ON THE
REMOVING TOOL OVER
WINGS ON LAMP SOCKET
REMOVING
TOOL
STROBE TUBE
INDEX NOTCHES
LOCATED INSIDE
REFLECTOR AND ON
LAMP SOCKET
HALOGEN
TUBE
GASKET
FIT WINGS ON THE
REMOVING TOOL OVER
WINGS ON LAMP SOCKET
REMOVING
TOOL
STROBE TUBE
INDEX NOTCHES
LOCATED INSIDE
REFLECTOR AND ON
LAMP SOCKET
HALOGEN
TUBE
GASKET
FIT WINGS ON THE
REMOVING TOOL OVER
WINGS ON LAMP SOCKET
REMOVING
TOOL
STROBE TUBE
INDEX NOTCHES
LOCATED INSIDE
REFLECTOR AND ON
LAMP SOCKET
HALOGEN
TUBE