PLANET POE-163 - Manual

- 1 -
- 2 -
- 3 -
- 4 -
- 5 -
- 6 -
- 7 -
- 8 -
1. Package Content
Thank you for purchasing PLANET IEEE 802.3at High
Power over Ethernet Injector, POE-163 and POE-164.
Model LAN Port Speed PoE Standard PoE Budget
POE-163 10/100/1000Mbps
802.3at/af 30Watts
POE-164 10/100Mbps
Terms of “802.3at PoE Injector” in following
section of this User’s Manual means the POE-163
and POE-164.
Upon open the box of the IEEE 802.3at High Power
over Ethernet Injector and carefully unpack it. The
box should contain the following items:
 The IEEE 802.3at High Power over Ethernet
Injector x 1
 User’s Manual x 1
 AC Power Cord x 1
If any of these are missing or damaged, please
contact your dealer immediately, if possible, retain
the carton including the original packing material,
and use them against to repack the product in case
there is a need to return it to us for repair.
2. Product Features
■ Interface
❏ 2-Port RJ-45 interfaces
› 1-Port Data + Power output
› 1-Port Data input
❏ 1 AC 100-240V input power socket
■ Power over Ethernet
❏ High Power over Ethernet Mid-Span PSE
❏ IEEE 802.3at PoE compliant
❏ Backward compatible with IEEE 802.3af PD
device
❏ Support PoE Power up to 30 Watts for PoE port
❏ Auto-detect of PoE IEEE 802.3at/af equipment
and devices from being damaged by incorrect
installation
❏ Remote power feeding up to 100m
■ Hardware
❏ Plastic case
❏ LED indicators for Power LED and Active LED
(PoE ready / In-use)
■ Standard Compliance
❏ IEEE 802.3 10Base-T
❏ IEEE 802.3u 100Base-TX
❏ IEEE 802.3ab 1000Base-T (POE-163 only)
❏ IEEE 802.3at High Power over Ethernet
❏ IEEE 802.3af Power over Ethernet
❏ FCC Part 15 Class B, CE
Note
PSE (Power Sourcing Equipment) is
a device (switch, or hub for instance)
that will provide power in a PoE setup.
Maximum allowed continuous output
power per such device in IEEE 802.3af
is 15.4W, 30W in IEEE 802.3at.
PD (Powered Device) is a PoE-enabled
terminal by PSE and thus consumes
energy, such as IP Phones, network
cameras and Wireless access points, etc
3. Product Specification
Product POE-163 POE-164
Hardware Specification
Interface
“Data” Input
Port
1 x RJ-45 STP
“PoE (Data
+ Power)”
Output Port
1 x RJ-45 STP
AC Input
power socket
1
LED Indicator
System: Power x 1 (Green)
PoE Port: Active, PoE ready / In
Use x 1 (Green)
Network Cable
10Base-T: 2-Pair UTP Cat. 3, 4, 5,
up to 100m (328ft)
100Base-TX: 2-Pair UTP Cat. 3, 4,
5, up to 100m (328ft)
1000Base-T: 2-Pair UTP Cat. 5,
5e, 6 up to 100m (328ft)
(POE-163 only)
EIA/TIA- 568 100-ohm STP (100m)
Data Rate 10/100/1000Mbps 10/100Mbps
Dimension (W x D x H) 115 x 62.5 x 31 mm
Weight
177g
Unit Output Voltage DC 53V, 0.6A
Power Requirement 100-240V AC, 50/60Hz, 0.75A
Power Consumption 30 Watts max.
Number of device can
be powered
1
Operating Temperature 0 ~ 50 Degree C
Storage Temperature
-10 ~ 70 Degree C
Operating Humidity
5 ~ 95%, Relative Humidity, non-
condensing
Storage Humidity
5 ~ 95%, Relative Humidity, non-
condensing
Power over Ethernet
PoE Standard
IEEE 802.3at High Power over
Ethernet / Mid-Span PSE
PoE Power Output DC 53V / 30 Watts
PoE Power Supply Type Mid-Span
Power Pin Assignment 4/5(+), 7/8(-)
Standards Conformance
Standards Compliance
IEEE 802.3 10Base-T Ethernet
IEEE 802.3u 100Base-TX Fast
Ethernet
IEEE 802.3ab 1000Base-T Gigabit
Ethernet
(POE-163 only)
IEEE 802.3at High Power over
Ethernet
IEEE 802.3af Power over Ethernet
Regulation Compliance FCC Part 15 Class B, CE
4. Product Outlook
Figure 1: shows overviews of 802.3at PoE Injector.
Figure 1: POE-163 / POE-164 Outlook
LED Indicators
LED Color Function
POWER Green
Lights to indicate that the 802.3at PoE
Injector has power.
ACTIVE Green
Slow blinks to indicate the port is not
providing 53V DC in-line power.
Lights to indicate the port is providing
53V DC in-line power.
5. Hardware Installation
The following section describes the hardware
features of 802.3at PoE Injector. Before connecting
any network device to the 802.3at PoE Injector, read
this chapter carefully.
This POE-163 provides three different running
speeds – 10Mbps / 100Mbps / 1000Mbps and the
POE-164 provides two different running speeds
– 10Mbps / 100Mbps in the same device for
automatically distinguishes the speed of incoming
connection. Please refer to following sections for
detail information about IEEE 802.3at High Power
over Ethernet Injector.
5-1 Before Installation
Before your installation, it is recommended to check
your network environment. If there is any IEEE
802.3at devices need higher power to power on and
work normally, the 802.3at PoE Injector can provide
you a way to supply power for this Ethernet device
conveniently and easily. The 802.3at PoE Injector
equips with an AC power cord with 100-240V AC
input and injects DC 53V power into the pin of the
twisted pair cable (pair 4, 5 [+] and pair 7, 8 [-] ).
If there is very difficult to find a power socket for
AC-DC Adapter of your non IEEE 802.3at networked
device, the 802.3at PoE Injector and POE-162S
can provide you a way to supply DC power for this
Ethernet device conveniently and easily.
Note
The 802.3at PoE Injector and POE-162S
can be installed in pair. However, the
use of third-party device is allowed if the
device complied with IEEE 802.3at Power
over Ethernet.
The 802.3at PoE Injector Installation
1. Connect the AC power cord to “AC slot” of
802.3at PoE Injector; the “POWER” LED will be
steady on.
2. Connect a standard network cable from Switch
/ workstation to “LAN” port of 802.3at PoE
Injector.
3. Connect the long cable that will be used to
connect to the remote device to the port “POE”.
4. Connect with IEEE 802.3at / 802.3af devices,
due to the capability of IEEE 802.3at / 802.3af
Power over Ethernet, the 802.3at PoE Injector
can directly connect with any IEEE 802.3at /
802.3af end-nodes such as PTZ (Pan, Tilt &
Zoom) network cameras, PTZ Speed Dome, color
touch- screen Voice over IP (VoIP) telephones,
multi- channel wireless LAN access points where
support IEEE 802.3at / 802.3af In-line Power over
Ethernet port. The screen in Figure 2 appears.
Switch
100 meters
PoE
Power Data
PoE PTZ
IP Camera 802.3at PoE Injector
Power
Data
AC
1000Base-T UTP
PoE 1000Base-T UTP with PoE
Power Line (AC) AC
Figure 2: Connection to IEEE 802.3at / 802.3af Devices