Hearth and Home Technologies MONTANA 42 EN - Manual (Page 34)

Outdoor Lifestyles by Hearth & Home Technologies Inc. • Montana US-CAN • 4039-156 Rev P • 10/12 34
C. Chimney Components
The following pictures show only those chimney components which may be safely used with this fireplace.
13 in.
(330 mm)
14 in.
(356 mm)
14 in.
(356 mm)
5-1/4 in.
(133 mm) 4 in. (102 mm)
CAK5A Chimney Air Kit
ID4 Insulated Duct
UD4 Uninsulated Duct
42 in.
(1067 mm)
4 in. (102 mm) i.d.
42 in.
(1067 mm)
4 in. (102 mm) i.d.
A
11 in.
(279 mm)
13 in.
(330 mm)
B
Chimney Sections
A = Actual Length
B = Effective Length (length of
chimney part after it has
been snapped to another)
SL11/SL4 Chimney Stabilizer
Outside Diameter
13 in./330 mm
Inside
Diameter
11 in./279 mm SL11
10 in./254 mm SL4
20-3/4 in.
527 mm
Catalog # A B
US CAN in mm in mm
SL1106 SL406 6 152 4-3/4 121
SL1112 SL412 12 305 10-3/4 273
SL1118 SL418 18 457 16-3/4 425
SL1136 SL436 36 914 34-3/4 883
SL1148 SL448 48 1219 46-3/4 1187
18 in.
(457 mm)
SLA10 Adapter
Catalog #
Description US CAN
CAK5A CAK5A Chimney Air Kit
n/a SLA10 Adapter 11 in. (457mm) long
ID4 ID4 Insulated Duct/Outside Air
UD4 UD4 Uninsulated Duct/Outside Air
SL1106 SL406 Chimney Section - 6 in. (152 mm) long
SL1112 SL412 Chimney Section - 12 in. (305 mm) long
SL1118 SL418 Chimney Section - 18 in. (457 mm) long
SL1136 SL436 Chimney Section - 36 in. (914 mm) long
SL1148 SL448 Chimney Section - 48 in. (1219 mm) long
SL11 SL4 Chimney Stabilizer
SL1130 SL430 Chimney Offset/Return - 30 deg
FS538 FS538 Ceiling Firestop - Straight
FS540 FS540 Ceiling Firestop - 30 deg
AS10 AS10 Straight Attic Insulation Shield, 24 in. (610 mm)
JB577 JB577 Chimney Joint Band
CB576 CB576 Chimney Bracket
RF570 RF570 Roof Flashing - Flat to 6/12 Pitch
RF571 RF571 Roof Flashing - 6/12 to 12/12 Pitch
TR11 TR444 Round Termination Cap
TR11T TR442 Round Telescoping Termination Cap
TCT1175 Terra Cotta Termination Cap
ST1175 ST475 Square Termination Cap
DTO134 DTO134 Short Octagon Decorative Cap
DTO146 DTO146 Tall Octagon Decorative Cap
DTS134 DTS146 Short Square Decorative Cap
DTS146 DTS146 Tall Square Decorative Cap
CT56 CT56 Chase Top
LDS33 LDS33 Decorative Shroud - 3 ft x 3 ft (.91 m x .91 m)
LDS46 LDS46 Decorative Shroud - 4 ft x 6 ft (1.22 m x 1.83 m)
LDS-BV LDS-BV
Decorative Shroud - 26 in. x 26 in.
(660 mm x 660 mm)
Field Constructed Shrouds (See “Woodburning
Termination Cap”)
CT-11A n/a Adapter-May be used with the following Copper Caps
n/a CT-Series
na DT-Series