Document Outline

• Go to Instruction Manual Top Page
  • COVER
  • PL
  • CONTENTS
  • 1. NAME OF MAJOR PARTS
  • 2. SPECIFICATIONS
  • 3. INSTALLATION
    • 3-1. Table processing diagram
    • 3-2. Positioning
    • 3-3. Installing the control box
    • 3-4. Installing the rubber cushions
    • 3-5. Installing the oil pan
    • 3-6. Installing the cushions
    • 3-7. Installing the switching plate
    • 3-8. Installing the machine head
    • 3-9. Tilting the sewing machine head
    • 3-10. Connecting the ground wire
    • 3-11. Connecting the cords (Installing the operation panel)
    • 3-12. Installing the belt cover
    • 3-13. Installing the foot switch
    • 3-14. Installing the spool stand
    • 3-15. Installing the eye guard
    • 3-16. Installing the programmer (option)
    • 3-17. Installing the work clamp lifter connecting rod
    • 3-18. Installing the feed base cover supports
    • 3-19. Installing the X feed base cover
    • 3-20. Connecting the tubes (pneumatic type only)
      • 3-20-1. Installing the air unit
      • 3-20-2. Adjusting the speed controller
  • 4. LUBRICATION
  • 5. CORRECT OPERATION
    • 5-1. Selecting the needle and thread
    • 5-2. Installing the needle
    • 5-3. Threading the upper thread
    • 5-4. Winding the lower thread
    • 5-5. Replacing the bobbin case and threading the thread
    • 5-6. Sewing conditions and thread tension
      • 5-6-1. Sewing conditions
      • 5-6-2. Lower thread tension
      • 5-6-3. Upper thread tension
      • 5-6-4. Thread take-up spring height
      • 5-6-5. Thread take-up spring tension
      • 5-6-6. Adjusting arm thread guide R
  • 6. USING THE OPERATION PANEL
    • 6-1. Explanation of panel
    • 6-2. Using the floppy disk
    • 6-3. Using the program R/W (Read/Write) switch
    • 6-4. Using the TEST switch (Checking the sewing pattern)
    • 6-5. Using the emergency stop switch
    • 6-6. Adjusting the sewing SPEED control
    • 6-7. Changing the X-SCALE and Y-SCALE settings
    • 6-8. Using the bobbin thread counter
    • 6-9. Using production counter
    • 6-10. Using single split mode
    • 6-11. Shifting a stitch pattern
  • 7. SEWING
    • 7-1. Before starting sewing....
    • 7-2. Sewing operation
  • 8. CLEANING AND INSPECTION
    • 8-1. Cleaning the rotary hook
    • 8-2. Lubrication
    • 8-3. Draining the oil
    • 8-4. Cleaning the control box air inlet port
    • 8-5. Cleaning the air holes of belt cover and frame side cover
    • 8-6. Cleaning the eye guard
    • 8-7. Checking the needle
  • 9. STANDARD ADJUSTMENTS
    • 9-1. Adjusting the needle bar height
    • 9-2. Adjusting the needle bar lift amount
    • 9-3. Adjusting the needle clearance
    • 9-4. Adjusting the driver needle guard
    • 9-5. Adjusting the shuttle race thread guide
    • 9-6. Adjusting the movable knife
    • 9-7. Adjusting the presser foot
    • 9-8. Changing the presser foot lift
    • 9-9. Adjusting the wiper
    • 9-10. Adjusting the two-step work clamp lift amount
      • 9-10-1. BAS-311F-0 Solenoid type
      • 9-10-2. BAS-311F-0, 311F-L Pneumatic type
      • 9-10-3. BAS-326F-0
      • 9-10-4. Adjusting the air pressure
    • 9-11. Adjusting the needle up stop position
    • 9-12. Checking the input sensor and DIP switch input
    • 9-13. Checking the input voltage
    • 9-14. Clearing all memory settings
  • 10. DIP SWITCH
    • 10-1. Panel DIP switch functions
    • 10-2. DIP switches inside the control box
  • 11. CHANGING SPECIAL FUNCTIONS AND USING THE MEMORY SWITCHES
  • 12. ERROR CODES
  • 13. GAUGE PARTS LIST ACCORDING TO SUBCLASSES
  • 14. TROUBLESHOOTING
  • BACK COVER