Document Outline

• FOREWORD
• SAFETY ALERT SYMBOLS AND SAFETY SIGNAL WORDS
  • Contact :
  • In USA:
  • Outside USA:
• REVISION LOG
• Section 1. SAFETY PRECAUTIONS
  • 1.1 General
  • 1.2 Pre-Operation
    • Operator Training and Knowledge
    • Workplace Inspection
    • Machine Inspection
  • 1.3 Operation
    • General
    • Trip and Fall Hazards
    • Electrocution Hazards
    • Tipping Hazards
    • Crushing and Collision Hazards
  • 1.4 Towing, Lifting, and Hauling
  • 1.5 Maintenance
    • Maintenance Hazards
    • Battery Hazards
• SECTION 2. PREPARATION AND INSPECTION
  • 2.1 Personnel Training
    • Operator Training
    • Training Supervision
    • Operator Responsibility
  • 2.2 Preparation, Inspection, and Maintenance
    • Pre-Start Inspection
    • Function Check
    • General
• SECTION 3. MACHINE CONTROLS, INDICATORS AND OPERATION
  • 3.1 Ground Control Station
  • 3.2 Platform/Remote Control Station
    • Maintenance Control Position On The Ground
    • Platform/Remote Control Position From The Ground
    • Control Position From In The Platform
    • Platform/Remote Control Station Functions
    • Platform/Remote Control Station LCD Display
• SECTION 4. MACHINE OPERATION
  • 4.1 DESCRIPTION
  • 4.2 BOOM OPERATING CHARACTERISTICS AND LIMITATIONS
    • Capacities
    • Stability
  • 4.3 ENGINE OPERATION
    • Gas Engine Starting Procedure
    • Gas Engine Shutdown Procedure
    • Electric Engine Starting Procedure - AC Voltage Machine
    • Electric Engine Starting Procedure - LITHIUM-ION Machine
  • 4.4 BASE AND BOOM/JIB ALIGNMENT
  • 4.5 TRACKS - DRIVING, STEERING AND TRACK WIDTH ADJUST
    • Track width adjust
    • Travelling (Drive and Steer)
    • Travelling (Grades and Side Slopes)
    • Jib Position for Travelling
  • 4.6 OUTRIGGER OPERATION
    • Setting Outriggers From the Platform/Remote Console
    • Retracting The Outriggers (Reference Figure 4-4. for item numbers)
  • 4.7 BOOM/PLATFORM OPERATION
    • Overload Alarm
    • Engine Pre-Heat
    • Platform Level Adjustment
    • Raise And Lower The Tower Boom
    • Raise And Lower The Main Boom
    • Telescope The Main Boom
    • Platform Rotation (Item 19, Figure 4-4.)
    • Raise And Lower The Jib (Item 20, Figure 4-4.)
  • 4.8 Platform Removal/Installation
  • 4.9 BATTERY CHARGING - GAS/AC-ELECTRIC
    • Battery Charging - Daily
  • 4.10 BATTERY CHARGING - LITHIUM-ION MACHINE
    • Charging the Battery Pack
    • Charge Curve
  • 4.11 SHUT DOWN AND PARK
  • 4.12 LIFTING AND TIE DOWN
    • Lifting - Outrigger Lifting Rings
    • Lifting - Fork Lift Pockets
    • Loading and Unloading the Machine on Transport Vehicles Using Ramps
    • Tie Down
  • 4.13 MACHINE DECALS
• Section 5. EMERGENCY PROCEDURES
  • 5.1 General
  • 5.2 Incident Notification
  • 5.3 Emergency Operation
    • Power Main Cut-Off Switch Location
    • Operator Unable to Control Machine
    • Platform or Boom Caught Overhead
    • Manual Descent with Engine Running and Electrical Power
    • Manual Descent with Engine Running but without Electrical Power (Combustion Engines Only)
    • Manual Descent without Engine and Electrical Power
    • Outrigger/Track Movement Emergency Procedure:
  • 5.4 Safety Devices Bypass Key Use
    • Using The Emergency Descent In The Case Of An Outrigger Losing Contact With The Ground
    • Machine Realignment Emergency Procedure
  • 5.5 Lithium-ION Battery Pack - Handling In Dangerous Conditions
    • Procedure For Handling Hot Cells
    • Procedure For Handling Vented Cells
    • Procedure For Exploded Cells
    • Lithium Battery Fire
• SECTION 6. GENERAL SPECIFICATIONS AND OPERATOR MAINTENANCE
  • 6.1 Introduction
  • 6.2 Operating Specifications
    • Dimensional Data
    • Chassis
    • Capacities
    • Engine Data
    • Lithium-Ion Specifications
    • Machine Major Component Weights
    • Performance
  • 6.3 Service/Maintenance
    • Lubrication
    • Rubber Track Maintenance/Replacement
    • Wear Pad Inspection
    • Turntable Attach Bolts
    • Battery Maintenance and Charging - Gas/AC-Electric
  • 6.4 ELECTRIC MOTOR MAINTENANCE
    • Electric Motor
  • 6.5 PLATFORM/REMOTE CONTROL SERVICE MENU
    • Service Button
    • Menu Input
    • Errors Menu
    • Working Hours Menu
    • Set-up Menu
    • Joystick Menu
  • 6.6 LITHIUM-ION MACHINE - MAINTAINANCE
    • Cleaning the Machine
    • Battery Pack System Components and Maintenance
    • Lithium-Ion Machine Fault Codes
    • BMS Fault Codes - (Battery Management System)
    • Battery Charger Fault Codes
• SECTION 7. INSPECTION AND REPAIR LOG