Document Outline

• 1 About this Manual
  • 1.1 Introduction
  • 1.2 Arrangement of the documentation
  • 1.3 Typographical conventions
    • 1.3.1 Warnings
    • 1.3.2 Notes
    • 1.3.3 Presentation
• 2 Identifying the instrument version
  • 2.1 Instrument description
  • 2.2 Type designation
  • 2.3 Accessories
• 3 Installation
  • 3.1 Location and climatic conditions
  • 3.2 Fitting in position
• 4 Electrical connection
  • 4.1 Notes on installation
  • 4.2 Connection diagram
• 5 Starting up
  • 5.1 Display and controls
  • 5.2 Opening and closing the door
  • 5.3 Marking the channel label
  • 5.4 Fitting the fibre pens
• 6 Preparation
  • 6.1 Operating modes and status
  • 6.2 Operating principle
• 7 Text printing
  • 7.1 Printing priorities
  • 7.2 Printing modes
  • 7.3 Clock time
  • 7.4 Scaling
  • 7.5 Changing the chart speed
  • 7.6 Recording start and end
  • 7.7 External text, binary-linked text, relay texts
  • 7.8 Incrementing the event counter
  • 7.9 Statistical report
  • 7.10 Print test
  • 7.11 Service print
• 8 Programming
  • 8.1 Basic status
  • 8.2 Operating level
    • 8.2.1 Chart speed
    • 8.2.2 Print test
    • 8.2.3 Service print
    • 8.2.4 Level inhibit and code request
  • 8.3 Parameter level
    • 8.3.1 Language
    • 8.3.2 Date and time
    • 8.3.3 Summer time
    • 8.3.4 Display brightness
    • 8.3.5 Relay limits
    • 8.3.6 Display of time
  • 8.4 Configuration level 1
    • 8.4.1 Writing status
    • 8.4.2 Measurement /signal input
    • 8.4.3 Scaling
    • 8.4.4 Channel designation
    • 8.4.5 Limit operation
    • 8.4.6 Plotarea (zoom)
    • 8.4.7 Presentation range (offset)
  • 8.5 Configuration level 2
    • 8.5.1 Instrument designation
    • 8.5.2 Speed programming mode
    • 8.5.3 Speed limit operation
    • 8.5.4 Timed operation
    • 8.5.5 Scale printing
    • 8.5.6 Time printing
    • 8.5.7 Pen offset compensation
    • 8.5.8 Statistical report
    • 8.5.9 Text at beginning
    • 8.5.10 Text at end
    • 8.5.11 Presetting
    • 8.5.12 Codenumber
  • 8.6 Configuration level 3
    • 8.6.1 Relay output
    • 8.6.2 Maths and logics module
    • 8.6.3 Interface
    • 8.6.4 External text
    • 8.6.5 Binary-linked external text
    • 8.6.6 External stop
    • 8.6.7 External speed
    • 8.6.8 Event counter
    • 8.6.9 External scaling
    • 8.6.10 External report
• 9 Consumables
  • 9.1 Summary of consumables
  • 9.2 Removing and replacing the chart cassette
    • 9.2.1 Changing the roll chart
    • 9.2.2 Changing the fanfold chart
• 10 Extra Codes and accessories
  • 10.1 Converting the chart cassette
  • 10.2 Extra Code 259
  • 10.3 External relay module ER8
  • 10.4 Setup program
  • 10.5 Maths and logics module
  • 10.6 Interface (RS422 / RS485)
• 11 Fault finding
  • 11.1 What to do if...
• 12 Appendix
  • 12.1 Technical Data
  • 12.2 Error messages
  • 12.3 Hardware fault
  • 12.4 Status messages
  • 12.5 Character set
  • 12.6 Summary of the parameters
• 13 Index
  • A
  • B
  • C
  • D
  • E
  • F
  • H
  • I
  • L
  • M
  • N
  • O
  • P
  • R
  • S
  • T
  • U
  • V
  • W
  • Z