Document Outline

• Content2
  • 1. Mounting 5
  • 2. Electrical connections 6
    • 2.1 Connecting diagram 6
    • 2.2 Terminal connection 7
  • 3. Operation 11
    • 3.1 Front view 11
    • 3.2 Behaviour after power-on 12
    • 3.3 Operating level 12
    • 3.4 Error list / Maintenance manager 13
    • 3.5 Self-tuning 15
      • 3.5.1 Preparation for self-tuning 16
      • 3.5.2 Optimization after start-up or at the set-point 16
      • 3.5.3 Selecting the method ( ConF / Cntr / tunE ) 17
      • 3.5.4 Self-tuning start 21
      • 3.5.5 Self-tuning cancellation 22
      • 3.5.6 Acknowledgement procedures in case of unsuccessful self-tuning 22
      • 3.5.7 Examples for self-tuning attempts 23
    • 3.6 Manual self-tuning 24
    • 3.7 Second PID parameter set 25
    • 3.8 Alarm handling 26
    • 3.9 Operating structure 28
  • 4. Configuration level 29
    • 4.1 Configuration survey 29
    • 4.2 Adjustment: 29
    • 4.3 Configuration parameters 30
    • 4.4 Set-point processing 47
    • 4.5 8840 profiler cooling functions 48
      • 4.5.1 Standard ( CyCl= 0 ) 48
      • 4.5.2 Heating and cooling with constant period ( CyCl= 3 ) 48
    • 4.6 Configuration examples 49
      • 4.6.1 On-Off controller / Signaller (inverse) 49
      • 4.6.2 2-point controller (inverse) 50
      • 4.6.3 3-point controller (relay & relay) 51
      • 4.6.4 3-point stepping controller (relay & relay) 52
      • 4.6.5 Continuous controller (inverse) 53
      • 4.6.6 D - Y - Off controller / 2-point controller with pre-contact 54
      • 4.6.7 8840 profiler with measured value output 55
      • 4.6.8 Continuous controller with integrated positioner ( Cntr/ C.Fnc = 6 ) 56
  • 5. Parameter setting level 57
    • 5.1 Parameter survey 57
    • 5.2 Parameters 58
    • 5.3 Input scaling 61
      • 5.3.1 Input Inp.1 and InP.3 61
      • 5.3.2 Input InP.2 61
  • 6. Calibration level 62
  • 7. Programmer level 65
    • 7.1 Parameter survey 65
    • 7.2 Parameters 66
    • 7.3 Programmer description 68
      • 7.3.1 General 68
      • 7.3.2 Programmer set-up: 69
      • 7.3.3 Operation 71
      • 7.3.4 Programmer display 72
      • 7.3.5 Segment type 73
      • 7.3.6 Bandwidth monitoring 74
      • 7.3.7 Search run at programmer start 74
      • 7.3.8 Behaviour after mains recovery or sensor error 74
  • 8. Special functions 75
    • 8.1 8840 profiler as Modbus master 75
    • 8.2 Linearization 76
  • 9. 8800/8840 Configurator 77
  • 10. Versions 78
  • 11. Technical data 79
  • 12. Safety hints 84
    • 12.1 Resetting to factory setting 85
  • 13. Notes 88
• Index
  • 0-9
    • 2-point correction 62
  • A
    • Alarm handling 26 - 27
  • B
    • Bargraph 11
    • BlueControl 77
    • Bus interface
      • Technical Data 81
  • C
    • Calibration level (CAL) 62 - 64
    • Certifications 82
    • Configuration examples
      • 2-point controller 50
      • 3-point controller 51
      • 3-point stepping controller 52
      • Continuous controller 53
      • D - Y -Off controller 54
      • Measured value output 55
      • Signaller 49
    • Configuration level
      • Configuration parameters 30 - 46
      • Parameter survey 29
    • Connecting diagram 6
    • Connecting examples
      • di2/3, 2-wire transmitter supply 8
      • INP2 current transformer 7
      • OUT1/2 heating/cooling 7
      • OUT3 as logic output 10
      • OUT3 transmitter supply 9
      • RS485 interface 9
    • Control inputs di1, di2, di3
      • Technical data 79
    • Cooling functions
      • Constant period 48
      • Standard 48
    • Current signal measuring range 79
  • D
    • Digital inputs di1, di2, di3
      • Configuration 40
      • Technical data 79
  • E
    • Environmental conditions 81
    • Equipment 78
    • Error list 13
  • F
    • Front view 11
  • I
    • Input INP1
      • Configuration 31
      • Parameters 59
      • Technical data 79
    • Input INP2
      • Configuration 33
      • Parameters 59
      • Technical data 79
    • Input INP3
      • Configuration 33
      • Parameters 59
      • Technical data 79
    • Input scaling 61
  • L
    • LED
      • Ada - LED 11
      • Err - LED 11
      • func - LED 11
      • ì - LED 11
      • LED colours 11
      • ò - LED 11
      • para - LED 11
      • SP.2 - LED 11
      • SP.E - LED 11
    • Linearisierung 76
  • M
    • Mainenance manager 13 - 14
    • Manual tuning 24
    • Modbus master 75
    • Mounting 5
  • O
    • Offset correction 62
    • Optimierung am Sollwert 18
    • Output OUT1
      • Configuration 37
      • Technical data 80
    • Output OUT2
      • Configuration 38
      • Technical data 80
    • Output OUT3
      • Configuration 38
      • Technical data 80
    • Output OUT4
      • Configuration 40
      • Technical data 80
    • Output OUT5
      • Configuration 40
      • Technical data 80
    • Output OUT6
      • Configuration 40
      • Technical data 80
  • P
    • Parameter setting level
      • Parameter survey 57
      • Parameters 58 - 60
    • Power supply 81
  • R
    • Resetting to factory setting 85
    • Resistance thermometer measuring range 79
  • S
    • Safety hints 84 - 85
    • Safety switch 5
    • Safety test 81
    • Self-tuning
      • Cancelation 22
      • Cancelation causes 22
    • Set-point processing 47
  • T
    • Thermocouple measuring range 79
  • V
    • Versions 78
    • Voltage signal measuring range 79