User instructions, General, Lighting the fire – Stovax PR0741 User Manual

Page 4: Turning the fire off, Upgrading your fire

Advertising
background image

USER INSTRUCTIONS

4

1. GENERAL

1.1 Installation and servicing must only be carried out by a

competent person.

1.2 In all correspondence, please quote the fire type and

serial number, which can be found on the data badge

adjacent to the control knob.

1.3 Ensure that curtains are not positioned above the fire, and

that there is a 300mm minimum clearance between the

sides of the fire and any curtains.

1.4 This product is guaranteed for 2 years from the date of

installation, as set out in the terms and conditions of sale

between Gazco and your local Gazco dealer. Please

consult with your local Gazco dealer if you have any

questions. In all correspondence always quote the Model

Number and Serial Number.

1.5 The decorative front and glass become hot during normal

use and should be treated as a ‘working surface’. It is

therefore recommended that a suitable fire guard be used

for protection of young children and the infirm.

1.6 If any cracks appear in the glass panel do not use the fire

until the panel has been replaced.

2. LIGhTING ThE FIRE

2.1 Locate the control valve on the fire. There are two control

knobs on the valve, the right-hand knob controls the pilot

ignition and the left hand knob controls the main burner.

2.2 If your fire has already been upgraded to battery

remote control, please refer to the instructions provided

with the upgrade to operate the remote control. The

following instructions work for either situation.

1

AR0914

• Ensure that the left-hand control knob is pointing to off (

).

• Ensure that the right-hand control knob is pointing to

off ( ).

• Press in the right-hand control knob and rotate it left until

a click is heard

• Keep pressing in and the knob is pointing to pilot (

)

The pilot should now light. If the pilot has not lit, repeat the

procedure until it does.

• Hold the control knob pressed in 10 seconds and then

release it

The pilot should stay alight. If the pilot goes out, repeat the

steps.

2.3 If the pilot does not light after repeated attempts, contact

the retailer or installer from whom the fire was purchased.

2.4 Turn the right-hand control to point to main burner (

).

The fire can now be controlled using the left-hand

control knob.

2.5 Turn the left-hand control knob to point to low fire (

),

the main burner now lights on low. The burner can

now be controlled between low and high settings.

Turn the control knob anti clockwise to increase the flame

height and clockwise to decrease the height.

2.6 If the pilot flame is extinguished, intentionally or

unintentionally, do not relight the appliance for at least

3 minutes.

3. TURNING ThE FIRE OFF

3.1 To turn the fire off, locate the control valve, turn the left-

hand control knob until it points to off ( ). The main burner

goes out leaving the pilot burning.

3.2 To turn the pilot off, locate the control valve, turn the right-

hand control knob until it points to off ( ). The pilot will

go out.

4. UPGRADING yOUR FIRE

4.1 Your fire is fitted with a control valve that can easily be

upgraded to battery powered remote control. This upgrade

can be fitted by anyone capable of simple DIY jobs and

requires no special training. This upgrade can be obtained

through your local Gazco stockist.

4.2 STANDARD REMOTE CONTROL This remote control can

control the fire after the pilot has been lit. It can turn the

main burner on and regulate it from low through to high

and back again. It can turn the main burner off leaving the

pilot burning GAZCO PART NUMBER 8455.

4.3 PROGRAMMABLE THERMOSTATIC AND TIMER REMOTE

CONTROL. This remote control can control the gas fire

after the pilot has been lit. In MANUAL MODE it can be

used to turn the main burner on and manually regulate it

from low through to high and back again. It can be used to

turn the main burner off, leaving the pilot burning. In

AUTO MODE it will automatically regulate the room

temperature to a preset temperature. In TIMER MODE it

will turn the fire on and off according to preset programme

and automatically regulate the room temperature during

the two periods. GAZCO PART NO. 8456.

Advertising