Grizzly G0605X/G0606X - Manual (Page 18)

-16-
G0605X/G0606X Extreme Series 12" Table Saw
Outfeed Table
Inventory
Box Contents: (Figure 8) Qty
A. Outfeed Table ............................................. 1
B. Lower Shelf ................................................ 1
C. Shelf End Plate ........................................... 1
D. Support Legs .............................................. 2
E. Lower Shelf Brackets ................................. 2
Hardware and Tools (Not Shown): Qty
• Flange Bolts M8-1.25 x 16
(Rear Rail/Ext. Table) ................................. 2
• Hex Nuts M8-1.25 (Rear Rail/Ext. Table) .. 2
• Hex Bolts M6-1 x 12
(Brackets/Legs/ Cabinet) ............................ 4
• Hex Nuts M6-1 (Bracket/Legs/Cabinet) ..... 2
• Hex Nuts 3 ⁄
8
-16 (Brackets/Legs/Cabinet) .... 2
• Flat Washers 6mm
(Brackets/Legs/Cabinet) ........................... 16
• Phillips Head Screws M6-1 x 12
(Legs/Ext. Table/End Plate) ..................... 12
• Feet 3 ⁄
8
-16 x 2 (Legs) .................................. 2
• Flange Bolts M8-1.25 x 12
(Tube/ Front Rail) ....................................... 9
Extension Table
Inventory
Box Contents: (Figure 7) Qty
A. Extension Table .......................................... 1
B. Lower Shelf ................................................ 1
C. Shelf End Plate ........................................... 1
D. Support Legs .............................................. 2
E. Lower Shelf Brackets ................................. 2
Hardware and Tools (Not Shown): Qty
• Cap Screws M8-1.25 x 25
(Rear Rail/Cabinet/Ext. Table) ................... 8
• Flat Head Screws M8-1.25 x 25
(Front Rail/Cabinet/Ext. Table) ................... 8
• Flat Washers 8mm
(Front Rail/Ext. Table/Rear Rail) .............. 16
• Hex Nuts M8-1.25
(Front Rail/Ext. Table/ Rear Rail) ............... 8
• Flange Bolts M8-1.25 x 12
(Tube/ Front Rail) ....................................... 9
• Lock Washers 8mm
(Rear Rail/Ext. Table) ................................. 8
• Hex Bolts M6-1 x 12
(Brackets/Cabinet/Legs) ............................. 4
• Hex Nuts M6-1
(Brackets/Cabinet) ...................................... 2
• Feet 3 ⁄
8
"-16 x 2 (Legs) ................................ 2
• Phillip Head Screws M6-1 x 12
(Ext. Table/Legs/End Plate) ..................... 12
• Flat Washers 6mm
(Ext Table/Legs/End Plate) ...................... 16
• Hex Nuts 3 ⁄
8
-16 (Feet) ................................. 2
• Flat Washers 10mm (Cabinet) ................... 2
• Hex Bolts M10-1.5 x 25 (Cabinet) .............. 2
Figure 7. Extension table components.
A
B
C
D E
In the event that any nonproprietary parts are
missing (e.g. a nut or a washer), we would be
glad to replace them; or for the sake of expedi-
ency, replacements can be obtained at your local
hardware store.
NOTICE: Some hardware/fasteners on the inven-
tory list may arrive pre-installed on the machine
or related components. Check these locations
before assuming that any items from the inventory
list are missing.
Figure 8. Outfeed table components.
A
B
C
D
E