JAI CB-141MCL User Manual
User's manual
Advertising
This manual is related to the following products:
Table of contents
Document Outline
- CMB-141MCL
- 1. General
- 2. Camera nomenclature
- 3. Main Features
- 4. Locations and Functions
- 4.1. CM-141MCL/CB-141MCL
- 4.2. CM-141PMCL/CB-141PMCL
- 5. Pin Assignment
- 5.1 12-pin Multi-connector (DC-in/GPIO/I
- 5.2 Digital Output Connector for Mini Ca
- 5.2.1 CM-141MCL/-RA and CB-141MCL/-RA
- 5.2.2 CM-141 PMCL /-RA and CB-141 PMCL/
- 5.3 DIP switch SW600
- 5.4 Input and output circuits
- 5.4.1 Iris video output
- 5.4.2 Trigger input
- 5.4.3 XEEN output
- 5.4.4 Camera Link interface
- 5.4.5 Video Output Bit allocation
- 6. Functions and Operations
- 6.1. Basic functions
- 6.1.1 Vertical Binning (CM-141MCL only
- 6.1.2 CB-141MCL Bayer mosaic filter
- 6.1.3 Partial Scanning (fixed rate and
- 6.1.4 Electronic Shutter
- 6.1.5 Auto-Iris Lens video output (12-
- 6.1.6 Auto-detect LVAL-sync / async ac
- 6.1.7 Rear panel indicator.
- 6.2. Sensor Layout and timing
- 6.2.1 CCD Sensor Layout
- 6.2.2 Horizontal timing
- 6.2.3 Vertical timing
- 6.2.4 Partial Scanning
- 6.2.5 Vertical binning
- 6.3. Operation Modes
- 6.3.1 Continuous operation
- 6.3.2 Edge Pre-select (EPS) Trigger Mo
- 6.3.3 Pulse Width Control (PWC) Trigge
- 6.3.4 Reset Continuous (RCT) trigger m
- 6.3.5 Smear less EPS Trigger mode
- 6.4. Operation Mode and Functions matr
- 7. Configuring the Camera
- 7.1 RS-232C control
- 7.2 Setting functions
- 7.2.1 Bit allocation. BA=0, BA=1, BA=2
- 7.2.2 Partial scan. SC=0 through 5.
- 7.2.3 Vertical binning VB=0, VB=1
- 7.2.4 Shutter mode. SM=0 and SM=1
- 7.2.5 Trigger input select. TI=0, TI=1.
- 7.2.6 Trigger polarity. TP=0, TP=1.
- 7.2.7 Gain level. GA=-84 through +670
- 7.2.8 Black level. BL=255 through BL=767
- 7.3 Save and Load Functions.
- 7.4 CM-140MCL / CB-140MCL command lis
- 8. Camera Control Tool for CM-141 MCL /
- 8.1 Camera Control Tool Interface
- 8.1.1 Camera Control Tool Bar
- 8.2 The About Window
- 8.3 Communication Window
- 8.4 Camera Control Window
- 8.5 Using the Camera Control Tool
- 9. External Appearance and Dimensions
- 10. Specifications
- 10.1 Spectral response
- 10.2. Specification table
- 11. Appendix
- 11.1. Precautions
- 11.2. Typical Sensor Characteristics
- 11.3. Caution when mounting a lens on
- 11.4. Caution when mounting the camera
- 11.5. Exportation
- 11.6. References
- Change History
- User's Record