KORG TRITON STUDIO V2 - Manual (Page 33)

28
The page menu command “Auto Sampling/HD Audio
Setup” has been added to the Sequencer P0: Play/REC,
Sampling/HD Audio page. (
☞p.17)
This convenient function automatically sets the relevant
parameters to the ideal settings for various operations such
as Sequencer mode sampling (e.g., In-Track Sampling),
recording using the “HD Audio Track,” two-channel mix-
down to create an audio CD, or bouncing tracks. (For the
automatically-set parameters and their values, refer to p.32)
When you execute this operation, the relevant parame-
ters will be set automatically. You cannot use the [COM-
PARE] key to revert to the prior settings.
The settings are automatically made for the most typi-
cal applications. After executing the auto setup opera-
tion, you can further adjust any of the parameters as
described in the
paragraphs for each item.
1. Initialize
This initializes the parameters related to sampling or audio
track recording.
1 Select “Auto Sampling/HD Audio Setup” to open the
dialog box.
2 Use the radio buttons to select Initialize.
3 To execute “Auto Sampling/HD Audio Setup,” press the
OK button
. If you decide to cancel, press the Cancel but-
ton . (For the automatically-set parameters and their val-
ues, refer to p.32)
2. Resample SEQ Play
This automatically makes the necessary settings for resam-
pling your keyboard performance in Sequencer mode.
■ Setup
1 Select “Auto Sampling/HD Audio Setup” to open the
dialog box.
2 Use the radio buttons to select Resample SEQ Play.
3 Use “Save to” to select the location to which the resam-
pled data will be written. (
☞PG p.5 “Save to”)
RAM: The resampled data will be written into sample
memory (RAM). If the “Convert to Program” option in
step
4 is checked, a new multisample will automatically
be created after resampling.
DISK:
The resampled data will be saved as a WAVE file
on the internal hard drive or a hard drive etc. connected
to the SCSI connector.
4 If you set “Save to” to RAM, checking “Convert to Pro-
gram” will convert the resampled data into a program of
the number you specify in “Program.” After resampling,
you can switch to Program mode and try out the data
immediately.
5 Use “Program” to specify the conversion-destination
program.
6 Press the OK button to execute “Auto Sampling/HD
Audio Setup.”
If you decide to cancel, press the Cancel
button . (For the automatically-set parameters and their
values, refer to p.32)
If “Save to” is set to RAM and you want to change the
RAM bank, use the page menu command “Select Bank
& Smpl No.”
(Sequencer 0–7A ☞PG p.56) to specify the
sampling-destination sample memory (RAM).
If “Save to” is set to DISK, use the Program mode page
menu command “Select Directory” (Program 0–3D
☞PG p.7) to specify the save-destination for the WAVE
file that is created by resampling.
■ Resample
7 Press SAMPLING [REC] and then SAMPLING
[START/STOP]
.
8 Start the sequencer playback or play live on the key-
board. You can play along with the sequencer during res-
ampling. If you are only playing live, and not using the
sequencer, sampling will begin with the first note-on.
(
☞PG p.4)
9 When you are finished performing, press the SAM-
PLING [START/STOP] key
.
If “Save to” is set to RAM (Convert to Program) and
you continue resampling without changing the settings,
the successive samples will automatically be assigned
to C#2, D2, ...
■ Listen to the resampled data
• If “Save to” was set to RAM (Convert to Program),
switch to Program mode, select the program that was
created, and play the C2 key to hear the program.
• If “Save to” was set to DISK, go to Program mode and
use the page menu command “Select Directory” to hear
the WAVE file that was created. (Program 0–3D
☞PG
p.7)
If you want to simultaneously resample the song play-
back and your keyboard performance, change “Trig-
ger”
(0–7b ☞PG p.56) to Sequencer START SW so that
resampling will begin the moment the sequencer starts.
If you also want to sample an external audio signal
from AUDIO INPUT etc. at the same time, go to the
Sequencer P0: Play/REC, Sampling/HD Audio page
and set Input 1, 2 “BUS (IFX/Indiv.) Select” to L/R.
(
☞BG p.46)
Auto Sampling/HD Audio Setup