Lincoln Electric COMMANDER 500 IM644-A - Manual (Page 28)

C-1 ACCESSORIES C-1
OPTIONAL FIELD INSTALLED
ACCESSORIES
K802N POWER PLUG KIT - Provides a plug for each recep-
tacle.
K857 28 ft. (8.5 m) or K857-1 100 ft. (30.4 m) REMOTE
CONTROL
- Portable control provides same dial range as
the output control on the welder from a location up to the
specified length from the welder. Has convenient plug for
easy connection to the welder. The Commander 500 is
equipped with a 6-pin connector for connecting the remote
control and a toggle switch for selecting
“ LOCAL ” output con-
trol or “ REMOTE ” output control.
K704 ACCESSORY SET - Includes 35 feet (10 m) of elec-
trode cable and 30 feet (9 m) of work cable, headshield, work
clamp and electrode holder. Cable is rated at 500 amps, 60%
duty cycle.
K953-1 TWO WHEEL TRAILER - For road, in-plant and yard
towing. Road towing with optional fender & light kit. (For high-
way use, consult applicable federal, state and local laws
regarding possible additional requirements)
K953-1 Trailer
K958-1 Ball Hitch
K958-2 Lunette Eye Hitch
K959-1 Fender & Light Kit
K965-1 Cable Storage Rack
K825-1 ETHER START KIT - Provides maximum cold weath-
er starting assistance for frequent starting below 10 o F (-12.2
o C). Required Ether tank is not provided with kit.
K899-1 SPARK ARRESTOR KIT - Easily mounts to standard
muffler.
K949-1 OIL DRAIN KIT - Includes ball valve, hose and
clamp.
K1690-1 (1 Duplex) GFCI Kit - Includes one UL approved
115V ground fault circuit interrupter duplex type receptacle
with cover and installation instructions. Replaces the factory
installed 115V duplex receptacle. The receptacle of the GFCI
duplex is rated at 20 amps, the maximum total current from
the GFCI duplex is limited to 20 amps. Two kits are required.
K1596-2 Dual Output Meters and Gauges - Dual output
meters provide preset ability of voltage for wire welding and
current for stick welding. Measures both current and voltage
when welding. Gauges include: battery ammeter, engine
temperature, and engine oil pressure. Fuel gauge is not avail-
able in kit form.
K1597-1 42vac Transformer Kit. - For products requiring 42
VAC power source.
K1751-1 Cool Weather Kit. -(For Codes Above 10600)
Designed to improve cold weather running in temperatures
between 0
° to -35 ° F(-10 ° to -37 ° C). Diverts warmer engine com-
partment air back into the cooling air.
RECOMMENDED OPTIONAL EQUIPMENT
STICK
K704 Accessory Kit which includes:
• Electrode holder and cable.
• Ground clamp and cable.
• Headshield.
K857 Remote Control Kit is optional for remote current control.
TIG
Magnum TIG Torch
Magnum Parts Kit and Argon gas
K930-ALL TIG Module (not required for scratch start DC TIG
welding)
K936-1 Control Cable
K870 Foot Amptrol
Also available:
K963-1/-2 Hand Amptrol
K814 Arc Start Switch
K937-22 Control Cable Extension
K937-45 Control Cable Extension
K844-1 Water Valve
WIRE FEED WELDING
• LN-25 • LN-7
• LN-23P • LN-8
• NA-3 • Spool Gun & K488 Module
• LN-742 (requires optional K1597-1 42vac transformer kit).
HIGH FREQUENCY GENERATORS FOR TIG
APPLICATIONS
The K799 Hi-Freq Unit and the K930-ALL TIG Modules are suit-
able for use with the Commander 500. The Commander is
equipped with the required R.F. bypass circuitry for the connec-
tion of high frequency generating equipment. The high frequen-
cy bypass network supplied with the K799 Hi-Freq Unit
does
NOT need to be installed into the Commander.
The Commander and any high frequency generating equipment
must be properly grounded. See the K799 Hi-Freq Unit and the
K930-All TIG Module operating manuals for complete instruc-
tions on installation, operation, and maintenance.
COMMANDER 500