Battery connections, Welding output cables, Installation – Lincoln Electric EAGLE SVM192-A User Manual

Page 10: Caution, Warning, Warning caution

Advertising
background image

3. Proper placement of the equipment on the trailer to

insure stability side to side and front to back when

being moved and when standing by itself while

being operated or serviced.

4. Typical conditions of use, i.e., travel speed; rough-

ness of surface on which the trailer will be operated;
environmental conditions.

5. Conformance with federal, state and local laws

(1)

(1) Consult applicable federal, state and local laws regarding specif-

ic requirements for use on public highways.

READ the engine operating and maintenance
instructions supplied with this machine.

FUEL (GASOLINE FUEL ONLY)

Fil the fuel tank with clean, fresh, lead-free gasoline. Observe fuel

gauge while filling to prevent overfilling.

INSTALLATION

A-4

A-4

EAGLE™ 10,000

BATTERY CONNECTIONS

Use caution as the electrolyte is a strong acid that can

burn skin and damage eyes.

------------------------------------------------------------------------------------------

This welder is shipped with the negative battery cable discon-

nected. Make sure that the Engine Switch is in the “OFF” posi-

tion and attach the disconnected cable securely to the negative

battery terminal before attempting to operate the machine. If the

battery is discharged and does not have enough power to start

the engine, see the battery charging instructions in the Battery

section.

NOTE: This machine is furnished with a wet charged battery; if

unused for several months, the battery may require a booster

charge. Be careful to charge the battery with the correct polarity.

WELDING OUTPUT CABLES

With the engine off, connect the electrode and work cables to the

studs provided. These connections should be checked periodi-

cally and tightened if necessary. Loose connections will result in

overheating of the output studs.

When welding at a considerable distance from the welder, be

sure you use ample size welding cables. Listed below are cop-

per cable sizes recommended for the rated current and duty

cycle. Lengths stipulated are the distance from the welder to

work and back to the welder again. Cable sizes are increased for

greater lengths primarily for the purpose of minimizing cable volt-

age drop.

TOTAL COMBINED LENGTH OF

ELECTRODE AND WORK CABLES

0-100 Ft.

(0-328 m)

100-200 Ft.

(328-656 m)

200-250 Ft.

(656-820 m)

225 Amps

100% Duty Cycle

1 AWG

1 AWG

1/0 AWG

CAUTION

OIL

The EAGLE 10,000 is shipped with the engine

crankcase filled with SAE 10W-30 oil. Check the oil

level before starting the engine. If it is not up to the full

mark on the dip stick, add oil as required. Make certain

that the oil filler cap is tightened securely. Refer to the

engine Owner’s Manual for specific oil recommenda-

tions.

LUBRICATION SYSTEM CAPACITY

(INCLUDING FILTER)

Kohler CH23S - 2.0 Quarts (1.9 Liters)

VEHICLE MOUNTING

Improperly mounted concentrated loads may cause unstable

vehicle handling and tires or other components to fail.

• Only transport this Equipment on serviceable vehicles which

are rated and designed for such loads.

• Distribute, balance and secure loads so vehicle is stable

under conditions of use.

• Do not exceed maximum rated loads for components such as

suspension, axles and tires.

• Mount equipment base to metal bed or frame of vehicle.

• Follow vehicle manufacturer’s instructions.

------------------------------------------------------------------------------------------

WARNING

• Stop engine while fueling.

• Do not smoke when fueling.

• Keep sparks and flame away

from

tank.

• Do not leave unattended while fueling.

• Wipe up spilled fuel and allow fumes

to clear before starting engine.

• Do not overfill tank, fuel expansion

may cause overflow.

--------------------------------------------------------------------------------

WARNING

GASOLINE

can cause fire

or explosion.

Damage to the fuel tank may cause

fire or explosion. Do not drill holes

in the EAGLE 10,000 base or weld to

the EAGLE 10,000 base.

-----------------------------------------------------------------------

WARNING

CAUTION

Return

to

Section

T

OC

Return

to

Section

T

OC

Return

to

Section

T

OC

Return

to

Section

T

OC

Return

to

Master

T

OC

Return

to

Master

T

OC

Return

to

Master

T

OC

Return

to

Master

T

OC

Advertising