Pioneer VSX-AX5Ai-G - Manual (Page 59)

Controlling other equipment 08
59
En
8 Repeat steps 3 – 7 for any other components you
want to control.
9 When you’re finished, use / (cursor up/down)
to select ‘*Exit*’ from the menu and press ENTER.
Programming signals from other
remote controls
If the preset code for your component is not available, or
the available preset codes do not operate correctly, you
can program signals from the remote control of another
component. This can also be used to program additional
operations (buttons not covered in the presets) after
assigning a preset code in
Recalling preset codes on
page 58.
1 Press and hold REMOTE SETUP for three seconds.
The REMOTE SETUP menu appears on the remote
control display.
2 Use / (cursor up/down) to select ‘Learning’
from the menu and press ENTER.
Select Function
flashes in the display.
3 Press the MULTI CONTROL button that matches
the connection for the component you want to
control.
For example, press DVD/LD if you want to program an
operation for the DVD player that you connected to the
DVD/LD terminals.
Select Key flashes in the display.
• You can’t assign the RECEIVER or TUNER buttons.
4 Select the button corresponding to the command
you want to teach the remote control.
For example, press if you want to program the play
command from your DVD player remote control.
LEARN flashes in the display.
• When programming TV CONT , you can only select
TV , or one of the TV CONTROL buttons.
5 Point the two remote controls towards each
other then press the corresponding button on the
other remote control that is sending (teaching) the
signal to this receiver’s remote control.
For example, if you want to learn the playback control
signal, press
.
• The remote controls should be 5–20cm apart, and the
LEARN icon should be flashing to indicate the
remote is ready to accept a signal.
If the operation has been learned , the display will show OK
If the operation hasn’t been learned the display will show
NG .
Continue? shows in the display (if Select Key is flashing,
go back to step 4). Go to step 6.
• If the remote display shows FULL , it means the
memory is full. See Clearing remote control settings
on page 69 to erase a programmed button you’re not
using to free up more memory.
• If NG keeps showing in the display, or the remote
control keeps on returning to step 4 ( Select Key
flashes in the display), it may be possible that the
command cannot be learned by this remote control.
Certain buttons represent operations that cannot be
learned from other remote controls. The buttons avail-
able are shown below:
6 Use / (cursor up/down) to select ‘Yes’ to
program additional signals for the current compo-
nent.
Repeat steps 4 and 5.
• To program signals for another component, select
No and repeat steps 2 through 5.
7 When you’re finished, use / (cursor up/down)
to select ‘*Exit*’ from the menu and press ENTER.
You will return to the REMOTE SETUP menu. Select
*Exit* again to exit.
DVD/LD
VCR2 VIDEO CD
TV/SAT TV CONT
MULTI CONTROL
VCR1 / DVR
CD-R/ TAPE1 MD/ TAPE2
REMOTE
SETUP
ENTER
5 – 20cm
SETUP
SOURCE DV D /L D VC R 2 DIMMER
LO U D NESS
TO NE
SIGNAL SEL
DNR
DISC
1 5 90
67
8
34
2 BASS/TREBLE
VIDEO SEL
HI-BIT DIRECT A CCESS SEARCH MODE ENTER GUIDE
SY STEM SETUP TUNER EDIT MPX TUNING
BAND DT V ON/OFF
D IS P M O D E TUNING
ST AT ION TV V O L MO VIE
M USIC
MUTE
ENTER
SURROUND
REMO TE SETUP
MODE
DT V MENU CL
ASS
TV C O N TR O L TV C H TV INPUT
INPUT MIDNIGHT MUL T I DH INPUT AC O U S T IC CA L SB CH MODE
STEREO/ DIRECT
ST AT ION VO L U M E
CHANNEL SUB TITLE
ENTER
TO P MENU
MENU AU D IO
RETURN TR AC K EXIT
+ 10
+ + +
+
+
+
CHANNEL
+ EFFECT/CH SEL
VIDEO
CD
TV /S AT
TV C O N T
MUL T I C O NTROL VC R 1 / DV R
CD-R/ TA P E 1 MD/ TA P E 2
MUL TI OPER ATION
SY STEM OFF
RECEIVER
TV
TUNER
RECEIVER
SOURCE TV
DIMMER LOUDNESS TONE
SIGNAL SEL DNR
DISC
1
5
9 0
6 7 8
3 4 2
BASS/TREBLE
VIDEO SEL HI-BIT
DIRECT ACCESS SEARCH MODE
ENTER
GUIDE SYSTEM SETUP
TUNER EDIT
MPX
TUNING BAND
DISP MODE
TUNING
STATION STATION
CHANNEL
SUB TITLE
ENTER
TOP MENU MENU
AUDIO RETURN
TRACK
EXIT
+10
+
+
+ CHANNEL
+
EFFECT/CH SEL
TEXT ON RF ATT
TEXT OFF CLASS
VSX-AX5Ai.book 59 ページ ２００４年６月２日 水曜日 午後３時２７分