Pioneer VSX-AX5Ai-G - Manual (Page 98)

Additional information 12
98
En
Video
When playing a DTS format LD
there is audible noise on the
soundtrack. • The input signal type is set to ANALOG . • Set the input signal type to DIGITAL (see Selecting the
input signal type on page 43)
Can't record audio. • You are trying to make an analog recording
from a digital signal, or a digital recording of
an analog source. •You can only record analog to analog, or digital to digital.
• The digital source is copy protected. • You can't record digital sources that have been copy
protected.
• The analog REC jacks have not been
connected properly.
• Check your analog connections (see Connecting analog
audio sources on page 26).
Subwoofer output is very low. • The bass attenuator is set too low. • See Bass Peak Level on page 93 to adjust the setting.
• The speaker settings result in very little
audio signal being sent to the subwoofer. • Change your subwoofer setting to one of the following in
the
Speaker Setting on page 55:
Front: SMALL / Subwoofer: YES
Front: LARGE / Subwoofer: PLUS
Everything seems to be set up
correctly, but the playback sound
is odd. • The speakers are out of phase. • Check that the positive/negative speaker terminals on
the receiver are matched with the corresponding
terminals on the speakers (page 28).
Noise or hum can be heard even
when there is no sound being
input. • There is electrical interference from another
component or appliance. • Check that personal computers or other digital
components connected to the same power source are not
causing interference.
There seems to be a time lag
between the speakers and the
output of the subwoofer. • The subwoofer channel can be delayed
slightly if run through a low-pass filter. • See Automatically setting up for surround sound on
page 12 to set up your system again using MCACC (this
will automatically compensate for a delay in the
subwoofer output).
Symptom Cause Remedy
Symptom Cause Remedy
No image is output when an
input is selected. • The video connections are incorrect. • Make sure the video component is connected correctly
(see pages 19–27).
• You are using component video
connections for your source, but not for your
TV. • Using the video converter, video signals can be
converted from a composite or S-video input to a
component video output, but not vice-versa. See
About the
video converter on page 16 for more on this.
• You are using component video
connections and the component video inputs
are assigned incorrectly. • Check Assigning the component video inputs on page 82
to make sure you’re assigned the correct input.
• The DVD/video player settings are incorrect. • Set correctly. Refer to the instruction manual supplied
with the DVD/video player.
• The video input selected on the TV monitor
is incorrect. • Set correctly. Refer to the instruction manual supplied
with the TV.
• Even though the sub room monitor is
connected properly, the multi-room feature is
switched off. • Press the MULTI ROOM&SOURCE ON/OFF button to
switch it on.
• The component video inputs are assigned
to a video component connected only to the
composite or S-Video terminals. • Check Assigning the component video inputs on page 82
to make sure the component video assign for that video
component is switched to
OFF .
The System Setup screen
doesn't appear.
• The MONITOR OUT jack hasn't been
connected.
• You connected your TV to the
MULTI ROOM
& SOURCE MONITOR OUT jack instead of
the main MONITOR OUT jack.
• Connect the MONITOR OUT jack to the TV monitor (see
Connecting your TV on page 18).
• Some TVs connected to the receiver with
component video cables do not display the
System Setup screen when the Color Burst
feature is on (this applies to the NTSC video
system format only).
• When the receiver is in standby, switch to COLOR
BURST OFF by holding down the MULTI JOG CONTROL
RETURN button and pressing STANDBY/ON . (the
current setting appears in the display).
VSX-AX5Ai.book 98 ページ ２００４年６月２日 水曜日 午後３時２７分