Pioneer VSX-AX5Ai-G - Manual (Page 96)

Additional information 12
96
En
No sound
Symptom Cause Remedy
No sound is output when an
input source is selected. • Improper connections. • Make sure you have properly connected the component
to the corresponding input on the back of the receiver
(see
Connecting your equipment on page 15).
• Sound is muted or the volume is turned
down. • Press MUTE or adjust the volume accordingly.
• Speakers are turned off or selected
improperly with the
SPEAKERS switch.
• Press SPEAKERS to select the proper speaker set (see
Switching the speaker system on page 71).
• The input signal type is incorrect. • Press SIGNAL SELECT to select the proper input signal
(see Selecting the input signal type on page 43).
• The multichannel analog inputs are
selected. • Press MULTI CH INPUT again (see Using the
multichannel analog inputs on page 42).
No sound output from the front
speakers. • The front speakers aren’t connected
properly. • See Installing your speaker system on page 28 to
connect them properly.
No sound from the surround or
center speakers. • Speaker settings are incorrect. (for
example, they have been set to
NO ).
• Check you speaker settings in Speaker Setting on
page 55.
• The surround and/or center levels are
turned down. • Check the levels in Channel Level on page 56.
• The surround and/or center speakers aren’t
connected properly. • Check Installing your speaker system on page 28 to
make sure the speakers are connected correctly.
• The STEREO listening mode has been
selected.
• Choose a surround listening mode (see Listening in
surround sound on page 38).
No sound from surround back
speakers. • Surround back speakers are set to NO . • Set the surround back speakers to LARGE or SMALL
(see Speaker Setting on page 55).
• The SB CH mode is switched off . • Set the surround back channel to SB CH ON (see
page 44).
• The source is not a 6.1 channel playback
source. • Choose an advanced effect listening mode (see
Listening in surround sound on page 38).
• The surround back speakers aren’t
connected properly. • Check Installing your speaker system on page 28 to
make sure the speakers are connected correctly.
• The surround back channel is on the 1
speaker setting, and your speaker is
connected to the right channel output. • Connect the speaker to the surround back left channel
output (
Installing your speaker system on page 28).
• The SB CH MODE is switched to AUTO and
the Dolby Surround EX / DTS ES software
you’re playing has no flag to indicate it is 6.1
compatible.
• You can still listen with surround back sound by setting
the surround back channel to
SB CH ON (page 44).
No sound from subwoofer. • The bass attenuator is set too low (for
example, the
-80 setting).
• See Bass Peak Level on page 93 to adjust the setting.
• The subwoofer isn’t connected properly, or
it is switched off. • Connect or switch on the subwoofer (see Installing your
speaker system on page 28).
• Make sure the sleep function on your subwoofer isn’t
activated.
• The subwoofer's settings are incorrect. • Set the subwoofer (see Speaker Setting on page 55) to
YES or PLUS .
• The crossover frequency is set too low. • Set the crossover frequency to a (higher) frequency that
matches your speaker characteristics (see
Crossover
Network on page 87)
• There is very little low frequency information
in your source. • Change your subwoofer setting to one of the following in
the
Speaker Setting on page 55:
Front: SMALL / Subwoofer: YES
Front: LARGE / Subwoofer: PLUS
• The subwoofer's levels are too low. • See Channel Level on page 56 to check the speaker
levels.
• Check the volume control on the subwoofer to make
sure it is turned up.
VSX-AX5Ai.book 96 ページ ２００４年６月２日 水曜日 午後３時２７分