Panasonic AJ-LT85P - Manual (Page 10)

[6] Edit Mode Setting Section
q ASMBL button
Press this to perform assemble editing. Check that the
button LED has lighted.
1ST EDIT (SHIFT+ASMBL): With VTR2, the registered
position for the 1ST EDIT preset value is automatically
set to -23 seconds. For details, refer to set-up menu item
No. 312 (1ST EDIT DUR).
w
V button/lamp
For inserting video signals, press this button. Check that
its lamp is lighted up.
e A1 button
Press this to insert the audio CH1 signals. Check that the
button LED has lighted.
DUMP (SHIFT+A1): Press this to download EDL data to
an external device (such as a personal computer).
r A2 button
Press this to insert the audio CH2 signals. Check that the
button LED has lighted.
LOAD (SHIFT+A2): Press this to upload EDL data from
an external device (such as a personal computer).
t TC button
Press this to insert the time code. Check that the button
LED has lighted.
EDL (SHIFT+TC): Press this to display the editing list on
the LCD screen.
y REC (STORE) button
REC: To set the VTR manually to the recording mode,
press this button and the PLAY button together.
When the REC button is pressed while the REC INHIBIT
switch is at OFF, the VTR2 video and audio CH1 and
CH2 will be set to the E-E mode while the button is held
down.
STORE (SHIFT+REC): Press these buttons to set the
VTR1 (playback) or VTR2 (recording) edit points and
store the edit data in the internal memory.
The EVENT counter is simultaneously incremented.
When the set-up operations are performed, the data
which has been set is saved in the set-up memory.
u EDIT (MENU) button
EDIT: Press this button to establish the E-E mode in
accordance with the edit mode. While it is held down, the
VTR2 video and audio input signals are output without
being recorded in accordance with the edit mode. To con-
duct a recording, press this button together with the PLAY
button in the VTR2 control section, while VTR2 is in the
playback mode.
MENU (SHIFT+EDIT): Press these buttons to perform
dial menu set-up.
i RESET button
• This resets the CTL counter on the VTR2 display sec-
tion.
• When the IN or OUT button is pressed together with the
RESET button, the registered IN or OUT point is
cleared.
CONTROLS AND THEIR FUNCTIONS
10
-
- - -
-
- -
-
- -
-
- -
-
- -
-
- -
-
- -
-
-
-
EJECT
V T R 1
POWER
REC
CH1
RESET
REC
DIAG
REMOTE
EXT VTR
LOCAL-
VTR1 VTR2
CONTROL
ON
OFF
REC
INHIBIT
OFF ON
CH2
PB
AUDIO LEVEL
REW FF
STOP STB OFF TRACK
PLAY STILL
1ST EDIT
BS EVENT
SPLIT
ASMBL
IN OUT
VTR1 VTR2 VTR1 VTR2
PREROLL
SYNCHRO
7
5
3
CF
ON
OFF
CH1
MIX
CH2
V1
V1•2
V2
SWAP
NORM
MIX
AUDIO
MONITOR
SPEAKER/
HEADPHONES
AUDIO
SWAP
DUMP LOAD EDL
CLEAR FS
RECALL
LAST
EDIT
V A1 A2 TC
PLAY
IN OUT
GO TO
ENTRY / SHIFT
EDIT MODE
COUNTER
CTL
TC
UB
VTR1
EJECT
V T R 2
RESET
REC
STORE
STOP STB OFF
MENU
EDIT
STILL REW FF
VTR2
REC
CH1 CH2
OPERATION MODE VTR2 AUDIO
INPUT SELECT EDIT
INT
EXT
SEPARATE CH1 CH2
VTR1
EXT
PB
AUDIO LEVEL
PREVIEW
REVIEW MULTI
AUTO EDIT ALL STOP
8
1 2 3 4 5 6 7