Pioneer BDP-320 - Manual (Page 43)

43
En
06
2 Select and set the method for switching the
speaker to be adjusted.
Use
/ to select, then press ENTER.
• Auto – Switch the speaker to be adjusted
automatically.
• Manual – Switch the speaker to be adjusted
manually.
3 Adjust the output level.
Use
/ to select, / to adjust.
Note
• You can also adjust while listening to the sound being
played (page 35).
• The volume of the test tones out put from the
subwoofe r may seem lower than the tones output
f rom the other channels. Adjust the subwoofer based
on the sound du ring playback (page 35).
• When Auto is selected, the speaker cannot be
selected with
/. In this case, test tones are not output from the
subwoofe
r.
 Setting the IP address
1 Select and set Network
 IP Address  Next
Screen.
Use
/ to select, then press ENTER.
2 Set IP address.
Use
/// to set the IP address of the player or DNS
se rver, then press ENTER.
• Auto Set IP Address
On – The player’s IP address is obtained
automatically. Select this when using a b
roadband
router or broadband modem that has a DHCP
(Dynamic Host Configu
ration Protocol) server
function. This player’s IP address will automatically
be allocated f rom the DHCP server.
Off – The player’s IP address must be set manually.
Use the numbe
r buttons (0 to 9) to input the IP
add ress, subnet mask and default gateway.
• Auto Set DNS Server Address
On – The DNS server’s IP address is obtained
automatically.
Off – The DNS server’s IP address must be set
manually. Use the numbe
r buttons (0 to 9) to input the
DNS se rver’s IP address stipulated by your Internet
se rvice provider.
Note
• When Auto Set IP Address is set to Off, Auto Set
DNS Server Address is also set to Off.
• Fo r information on DHCP server function, refer to the
netwo rk device’s operating instructions.
• You may need to contact you r Internet service
provider or network administrator when inputting the
IP add
ress manually.
 Setting the proxy server
Only set the proxy server if so instructed by your Internet
se rvice provider.
1 Select and set Network  Proxy Server  Next
Screen.
Use
/ to select, then press ENTER.
2 Select and set Use or Not use at Proxy Server.
Use / to change, then press .
• Use – Select this when using a proxy server.
• Not use – Select this when not using a proxy server.
If you have selected Use, proceed to step 3.
3 Select and set Server Select Method.
Use / to change, then press .
• IP Address – Input the IP address.
• Server Name – Input the server name.
4 Input IP Address or Server Name.
Use the numbe r buttons (0 to 9) to input the number if you
select IP add ress by step 3. Use
/ to move the cursor.
Use the numbe r buttons (0 to 9) to input characters if you
select Se rver Name by step 3.
The cha racters that can be input for the server name are
listed on the table below. P ressing a button repeatedly
cycles th rough the characters shown.
L
C
R
SR
SBR
SBL
SL
SW 0.0 dB
0.0 dB
0.0 dB
0.0 dB
0.0 dB
0.0 dB
0.0 dB
0.0 dB
Channel Level
BD PLAYER
IP Address
Auto Set IP Address
IP Address
Subnet Mask
Default Gateway
Auto Set DNS Server Address
DNS Server (Primary)
DNS Server (Secondary)
Off
Network
BD PLAYER
Off 
Use 
Proxy Server
Proxy Server
Server Select Method
Server Name
Port Number
Server Name
Network
BD PLAYER
320_UXJCA_EN.book 43 ページ ２００９年２月１３日 金曜日 午後４時２６分