Roland SH-201 - Manual (Page 63)

63
Parameter list
Parameter list
EFFECTS parameters
Parameter Value Explanation Panel operation
DELAY
DELAY
Switch OFF, ON Turns DELAY on/off.
1.
Press the EDIT
button so the
DELAY indi-
cator is lit
2. Press the FX ON button (p. 44)
HF DAMP 200, 250, 315, 400,
500, 630, 800, 1000,
1250, 1600, 2000,
2500, 3150, 4000,
5000, 6300, 8000
(Hz), BYPASS Adjusts the frequency above which the
high-frequency content of the delay sound
will be reduced.
If you do not want to reduce the high fre-
quencies, set this parameter to BYPASS.
2. Hold down the FX ON button
and turn the DEPTH knob
TIME 0–127 Adjusts the spacing between delay sounds
(the delay time). 2. Turn the TIME knob (p. 45)
DEPTH
LOWER 0–127 Adjusts the amount of delayed sound (the
delay level). 2. Press the LOWER button and
then turn the DEPTH knob (p. 45)
DEPTH
UPPER 0–127 Adjusts the amount of delayed sound (the
delay level). 2. Press the UPPER button and then
turn the DEPTH knob (p. 45)
FEEDBACK -98– +98 (%) Adjusts the amount of the delay sound fed
back into the effect.
Negative (-) settings invert the phase.
2. Hold down the FX ON button
and turn the TIME knob
(selectable value: 0– +98)
MODULA-
TION RATE 0–127 Specifies the speed of modulation that will
be applied to the delay sound. 2. Hold down the FX ON button
and move the AMP ENV R slider
MODULA-
TION DEPTH 0–127 Specifies the depth of modulation that will
be applied to the delay sound. 2. Hold down the FX ON button
and move the AMP ENV S slider
REVERB
REVERB
Switch OFF, ON Turns REVERB on/off.
1.
Press the EDIT
button so the
REVERB indi-
cator is lit
2. Press the FX ON button (p. 44)
PRE DELAY 0.0–100.0 (ms) Adjusts the delay time from the direct
sound until the reverb sound is heard. 2. Hold down the FX ON button
and turn the TIME knob
SIZE 1–8 Specifies the size of the simulated room or
hall. 2. Hold down the FX ON button
and move the FILTER ENV R
slider
HIGH CUT 160, 200, 250, 320,
400, 500, 640, 800,
1000, 1250, 1600,
2000, 2500, 3200,
4000, 5000, 6400,
8000, 10000, 12500
(Hz), BYPASS Adjusts the frequency above which the
high-frequency content of the reverb sound
will be reduced.
If you do not want to reduce the high fre-
quencies, set this parameter to BYPASS.
2. Hold down the FX ON button
and turn the DEPTH knob
TIME 0–127 Adjusts the length of reverberation (the re-
verb time). 2. Turn the TIME knob (p. 45)
DEPTH
LOWER 0–127 Adjusts the amount of reverb sound (the re-
verb level). 2. Press the LOWER button and
then turn the DEPTH knob (p. 45)
DEPTH
UPPER 0–127 Adjusts the amount of reverb sound (the re-
verb level). 2. Press the UPPER button and then
turn the DEPTH knob (p. 45)
DENSITY 0–127 Adjusts the density of reverb. 2. Hold down the FX ON button
and move the FILTER ENV S slid-
er
HF DAMP
FREQUENCY 4000, 5000, 6400,
8000, 10000, 12500
(Hz) Adjusts the frequency above which the
high-frequency content of the reverb sound
will be reduced or “damped.” 2. Hold down the FX ON button
and move the AMP ENV S slider
HF DAMP
GAIN -36–0 (dB) Adjusts the amount of damping applied to
the high-frequency range. 2. Hold down the FX ON button
and move the AMP ENV R slider
DIFFUSION 0–127 Adjusts the change in the density of the re-
verb over time.
The higher the value, the more the den-
sity increases with time.
2. Hold down the FX ON button
and move the FILTER ENV D
slider
LF DAMP
FREQUENCY 50, 64, 80, 100, 125,
160, 200, 250, 320,
400, 500, 640, 800,
1000, 1250, 1600,
2000, 2500, 3200,
4000 (Hz) Adjusts the frequency below which the low-
frequency content of the reverb sound will
be reduced or “damped.” 2. Hold down the FX ON button
and move the AMP ENV A slider
LF DAMP
GAIN -36–0 (dB) Adjusts the amount of damping applied to
the low-frequency range. 2. Hold down the FX ON button
and move the AMP ENV D slider
SH-201_r_e.book 63 ページ ２００６年４月２７日 木曜日 午前１１時２８分