Roland SH-201 - Manual (Page 65)

65
Parameter list
Parameter list
Parameter Value Explanation Panel operation
CONTROLLER ASSIGN
MODULATION OSC1&OSC2,
OSC1, OSC2,
PW1, PW2,
FILTER, AMP,
AUDIO-FILTER Selects the parameter to be modulated by the modulation
lever (p. 18). 1. Hold down the CANCEL button
and press the TAP button
2. Press the USER button and then
press the BANK A button
3. Press a NUMBER button (1–8)
1: OSC1&OSC2, 2: OSC1, 3: OSC2,
4: PW1, 5: PW2, 6: FILTER, 7: AMP,
8: AUDIO-FILTER
4. Press the CANCEL button
D BEAM Selects the parameter to be controlled by the D Beam controller if the D BEAM
FILTER/ASSIGN button is pressed.
Value:
OSC1-PITCH, OSC1-DETUNE, OSC1-PW,
OSC2-PITCH, OSC2-DETUNE, OSC2-PW,
MIX/MOD-BALANCE,
FILTER-CUTOFF, FILTER-RESONANCE,
FILTER-CUTOFF-KEYFOLLOW, AMP-LEVEL,
AUDIO-FILTER-CUTOFF, AUDIO-FILTER-RESONANCE,
PITCH-ENV-A, PITCH-ENV-D,
OSC1-PITCH-ENV-DEPTH, OSC2-PITCH-ENV-DEPTH,
LFO1-RATE, LFO1-DEPTH1, LFO1-DEPTH2,
LFO2-RATE, LFO2-DEPTH1, LFO2-DEPTH2,
FILTER-ENV-A, FILTER-ENV-D, FILTER-ENV-S,
FILTER ENV-R, FILTER-ENV-DEPTH,
AMP-ENV-A, AMP-ENV-D, AMP-ENV-S, AMP-ENV-R,
EFFECTS-DELAY-TIME, EFFECTS-DELAY-DEPTH,
EFFECTS-REVERB-TIME, EFFECTS-REVERB-DEPTH, BENDER
Hold down the D BEAM FILTER/AS-
SIGN button and move the knob or
slider of the desired parameter (p. 21).
CONTROLLER DESTINATION
MODULATION UPPER,
LOWER,
BOTH Selects the tone(s) to be modulated by the modulation lever.
If this is “BOTH,” modulation will be applied to both the
UPPER tone and LOWER tone.
1. Hold down the CANCEL button
and press the TAP button
2. Press the USER button and then
press the BANK B button
3. Press a NUMBER button (1–3)
1: UPPER, 2: LOWER, 3: BOTH
4. Press the CANCEL button
D BEAM UPPER,
LOWER,
BOTH Selects the tone(s) to be controlled by the D Beam controller.
If this is “BOTH,” both the UPPER tone and LOWER
tone will be controlled.
Hold down the D BEAM FILTER/AS-
SIGN button and press the UPPER/
LOWER buttons
PITCH BEND UPPER,
LOWER,
BOTH Selects the tone(s) whose pitch will be changed by the pitch
bend lever.
If this is “BOTH,” the pitch of both the UPPER tone and
LOWER tone will change.
1. Hold down the CANCEL button
and press the TAP button
2. Press the USER button and then
press the BANK C button
3. Press a NUMBER button (1–3)
1: UPPER, 2: LOWER, 3: BOTH
4. Press the CANCEL button
EXPRESSION UPPER,
LOWER,
BOTH Selects the tone(s) for which the expression pedal will con-
trol dynamics.
If this is “BOTH,” the dynamics of both the UPPER tone
and LOWER tone will be controlled.
1. Hold down the CANCEL button
and press the TAP button
2. Press the USER button and then
press the BANK D button
3. Press a NUMBER button (1–3)
1: UPPER, 2: LOWER, 3: BOTH
4. Press the CANCEL button
D BEAM
D BEAM
POLARITY +, - Specifies the direction in which the value will change when
the D BEAM’s FILTER/ASSIGN button is lit.
“+” and “-” will invert the direction of change.
* This will not change the direction of the change that oc-
curs when the PITCH button or EXPRESS button is lit.
Hold down the D BEAM FILTER/AS-
SIGN button and choose the direction
in which the value will be changed by
moving the knob or slider of the de-
sired parameter (p. 21).
ACTIVE
EXPRESSION OFF, ON Specifies the operation performed by the D Beam controller
when you press the D BEAM's EXPRESS button so it is lit.
OFF: The D Beam controller will change the volume.
ON: The D Beam controller will control Active Expres-
sion (p. 20) which combines two tones.
Hold down the CANCEL button and
press the D BEAM EXPRESS button
SH-201_r_e.book 65 ページ ２００６年４月２７日 木曜日 午前１１時２８分