Onkyo FR-N3X - Manual (Page 3)

3
20. Damage Requiring Service – Unplug the appliance form
the wall outlet and refer servicing to qualified service per-
sonnel under the following conditions:
A. When the power-supply cord or plug is damaged
B. If liquid has been spilled, or objects have fallen into the
appliance
C. If the appliance has been exposed to rain or water
D. If the appliance does not operate normally as per the
operating instructions. Adjust only those controls that are
covered by the operating instructions as an improper
adjustment of other controls may result in damage and
will often require extensive work by a qualified technician
to restore the appliance to its normal operation.
E. If the appliance has been dropped or damaged in any
way, and
F. When the appliance exhibits a distinct change in perfor-
mance – this indicates a need for service.
21. Replacement Parts – When replacement parts are
required, be sure the service technician has used replace-
ment parts specified by the manufacturer or that have the
same characteristics as the original part. Unauthorized sub-
stitutions may result in fire, electric shock, or other hazards.
22. Safety Check – Upon completion of any service or repairs
to the appliance, ask the service technician to perform
safety checks to determine that the appliance is in proper
operating condition.
23. Wall or Ceiling Mounting – The appliance should be
mounted to a wall or ceiling only as recommended by the
manufacturer.
24. Heat – The appliance should be situated away from heat
sources such as radiators, heat registers, stoves, or other
appliances (including amplifiers) that produce heat.
25. Liquid Hazards – The appliance shall not be exposed to
dripping or splashing and no objects filled with liquids, such
as vases shall be placed on the appliance.
FIGURE 1:
EXAMPLE OF ANTENNA GROUNDING AS PER NATIONAL
ELECTRICAL CODE, ANSI/NFPA 70
Precautions
1. Recording Copyright
Recording of copyrighted material for other than personal use
is illegal without permission of the copyright holder.
2. AC Fuse
The fuse is located inside the chassis and is not user-service-
able. If power does not come on, contact your Onkyo autho-
rized service station.
3. Power
WARNING
BEFORE PLUGGING IN THE UNIT FOR THE FIRST TIME,
READ THE FOLLOWING SECTION CAREFULLY.
The voltage of the available power supply differs according to
country or region. Be sure that the power supply voltage of the
area where this unit will be used meets the required voltage
(e.g., AC 230 V, 50 Hz or AC 120 V, 60 Hz) written on the rear
panel.
Setting the STANDBY button to standby mode does not shut
off the power completely.
4. Do not touch this unit with wet hands.
Do not handle this unit or power cord when your hands are wet
or damp. If water or any other liquid enters the case, take this
unit to an authorized service center for inspection.
5. Location of this unit
Place this unit in a well-ventilated location.
Take special care to provide plenty of ventilation on all sides of
this unit especially when it is placed in an audio rack. If ventila-
tion is blocked, this unit may overheat and malfunction.
Do not expose this unit to direct sunlight or heating units as
this unit's internal temperature may rise and shorten the life of
the pickup.
Avoid damp and dusty places and places directly affected by
vibrations from the speakers. In particular, avoid placing the
unit on or above one of the speakers.
Be sure this unit is placed in a horizontal position. Never place it
on its side or on a slanted surface as it may malfunction.
Do not place this unit near tuners or TV sets.
If placed next to a TV or tuner, it may cause reception interfer-
ence resulting in some noise in the TV or tuner output.
6. Care
From time to time you should wipe the front and rear panels
and the cabinet with a soft cloth. For heavier dirt, unplug the
power cord from the AC outlet, dampen a soft cloth in a weak
solution of mild detergent and water, wring it out dry, and wipe
off the dirt. Following this, dry the unit immediately with a
clean cloth.
Do not use rough material, thinners, alcohol or other chemical
solvents or cloths since these could damage the finish or
remove the panel lettering.
7. Points to remember
If this unit is brought from a cold environment to a warm one or
is in a cold room that is quickly heated, condensation may
form on the pickup, preventing proper operation. In this case,
remove the disc and leave the power ON for about one hour to
remove the condensation.
When transporting this unit, be careful not to bump it.
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
NEC – NATIONAL ELECTRICAL CODE
ELECTRIC
SERVICE
EQUIPMENT
GROUND
CLAMP
ANTENNA
LEAD IN
WIRE
S2898A
US and foreign patents licensed from Dolby Laboratories
Licensing Corporation.
“CLASS 1 LASER
PRODUCT ”
This unit contains a semiconductor laser system and is classified as a “CLASS 1
LASER PRODUCT.” To use this model properly, read this Instruction Manual
carefully. In case of any trouble, please contact the store where you purchased the
unit. To prevent being exposed to the laser beam, do not try to open the enclosure.
DANGER:
INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCK FAILED OR
DEFEATED. AVOID DIRECT EXPOSURE TO BEAM.
CAUTION:
THIS PRODUCT UTILIZES A LASER. USE OF CONTROLS OR ADJUSTMENTS
OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED
HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
This unit is a CLASS 1 LASER PRODUCT
and employs a laser inside the cabinet.
To prevent the laser from being exposed,
do not remove the cover. Refer servicing to
qualified personnel. 1.
2.
This label on the left hand panel states that: