Onkyo TX-SA706 - Manual (Page 116)

116
Troubleshooting
—Continued
• If your TV is connected to the HDMI OUT, select “- -
- - -” in the “HDMI Input Setup” on page 42 to watch
composite video, S-Video, and component video
sources.
• If the video source is connected to a component video
input, you must assign that input to an input selector
(page 43), and your TV must be connected to either
the HDMI OUT or COMPONENT VIDEO MONI-
TOR OUT (pages 25 and 34).
• If the video source is connected to an S-Video or com-
posite video input, your TV must be connected to the
HDMI OUT or the corresponding S-Video or compos-
ite video output (pages 25 and 34).
• If the video source is connected to an HDMI input,
you must assign that input to an input selector
(page 42), and your TV must be connected to the
HDMI OUT (page 34).
• While the Pure Audio listening mode is selected, the
video circuitry is turned off and only video signals
input through HDMI IN can be output.
• On your TV, make sure that the video input to which
the AV receiver/AV amplifier is connected is selected.
There’s no picture from a source connected to
an HDMI IN
• Reliable operation with an HDMI-to-DVI adapter is
not guaranteed. In addition, video signals from a PC
are not supported (page 34).
• When the “Output Resolution” (page 92) is set to any
resolution not supported by the TV, no video is output
by the HDMI OUT.
The onscreen menus don’t appear
• On non-North American models, specify the TV sys-
tem used in your area in the “TV Format Setup” on
page 46.
• On your TV, make sure that the video input to which
the AV receiver/AV amplifier is connected is selected.
The picture is distorted
• On non-North American models, specify the TV sys-
tem used in your area in the “TV Format Setup” on
page 46.
The immediate display does not appear
• The immediate display will not appear when the input
signal from the COMPONENT VIDEO IN is output to
a device connected to the COMPONENT VIDEO
MONITOR OUT.
• Depending on the input signal, the immediate display
may not appear when the input signal from the HDMI
IN is output to a device connected to the HDMI OUT.
Reception is noisy, FM stereo reception is
noisy, or the FM STEREO indicator doesn’t
appear
• Relocate your antenna.
• Move the AV receiver away from your TV or com-
puter.
• Listen to the station in mono (page 57).
• When listening to an AM station, operating the remote
controller may cause noise.
• Passing cars and airplanes can cause interference.
• Concrete walls weaken radio signals.
• If nothing improves the reception, install an outdoor
antenna.
The remote controller doesn’t work
• Make sure that the batteries are installed with the cor-
rect polarity (page 14).
• Install new batteries. Don’t mix different types of bat-
teries, or old and new batteries (page 14).
• Make sure that the remote controller is not too far
away from the AV receiver/AV amplifier, and that
there’s no obstruction between the remote controller
and the AV receiver/AV amplifier’s remote control
sensor (page 14).
• Make sure that the AV receiver/AV amplifier is not
subjected to direct sunshine or inverter-type fluores-
cent lights. Relocate if necessary.
• If the AV receiver/AV amplifier is installed in a rack or
cabinet with colored-glass doors, the remote controller
may not work reliably when the doors are closed.
• Make sure you’ve selected the correct remote control-
ler mode (pages 15 and 104-110).
• When using the remote controller to control other
manufacturers’ AV components, some buttons may
not work as expected.
• Make sure you’ve entered the correct remote control code.
• Make sure to set the same ID on both the AV receiver/
AV amplifier and remote controller (page 91).
Can’t control other components
• If it’s an Onkyo component, make sure that the
cable and analog audio cable are connected properly.
Connecting only an
cable won’t work (page 39).
• Make sure you’ve selected the correct remote control-
ler mode (pages 15 and 104-110).
• If you’ve connected an -capable Onkyo MD
recorder, CD recorder, RI Dock to the TAPE IN/OUT
jacks, or an RI Dock to the GAME/TV IN jacks, for
the remote controller to work properly, you must set
the display to MD, CDR, or DOCK (page 48).
If you cannot operate it, you will need to enter the
appropriate remote control code (page 102).
• To control another manufacturer’s component, point
the remote controller at that component.
Tuner (TX-SR706 only)
Remote Controller