Onkyo TX-SA706 - Manual (Page 12)

12
Front & Rear Panels
—Continued
REMOTE CONTROL
This (Remote Interactive) jack can be con-
nected to an jack on another Onkyo AV compo-
nent. The AV receiver/AV amplifier’s remote
controller can then be used to control that compo-
nent. To use
, you must make an analog audio
connection (RCA) between the AV receiver/AV
amplifier and the other AV component, even if they
are connected digitally.
PHONO IN
This audio input is for connecting a turntable.
COMPONENT VIDEO IN 1 and 2
These RCA component video inputs are for con-
necting components with a component video out-
put, such as a DVD player, DVD recorder, or DVR
(digital video recorder). They’re assignable, which
means you can assign each one to an input selector
to suit your setup. See “Component Video Setup”
on page 43.
COMPONENT VIDEO MONITOR OUT
This RCA component video output is for connect-
ing a TV or projector with a component video input.
HDMI IN 1–4 and OUT
HDMI (High Definition Multimedia Interface) con-
nections carry digital audio and digital video.
The HDMI inputs are for connecting components
with an HDMI output, such as a DVD player, DVD
recorder, or DVR (digital video recorder). They’re
assignable, which means you can assign each one to
an input selector to suit your setup. See “HDMI
Input Setup” on page 42.
The HDMI output is for connecting a TV or projec-
tor with an HDMI input.
MONITOR OUT
The S-Video or composite video jack should be
connected to a video input on your TV or projector.
IR IN
A commercially available IR receiver can be con-
nected to the IR IN jack, allowing you to control the
AV receiver/AV amplifier while you’re in Zone 2, or
control it when it’s out of sight, for example,
installed in a cabinet.
12V TRIGGER OUT ZONE 2
This output can be connected to the 12-volt trigger
input on a component in Zone 2. When Zone 2 is
turned on on the AV receiver/AV amplifier, a 12-
volt trigger signal is output.
FM ANTENNA (TX-SR706 only)
This jack is for connecting an FM antenna.
AM ANTENNA (TX-SR706 only)
These push terminals are for connecting an AM
antenna.
RS232
This is the RS232 port.
XM antenna (North American models only)
This jack is for connecting an XM Mini-Tuner and
Home Dock, sold separately (see the separate XM
instructions).
SIRIUS antenna (North American models
only)
This jack is for connecting a SIRIUS Satellite Radio
antenna, sold separately (see the separate SIRIUS
instructions).
AC INLET (not North American models)
The supplied power cord is connected here. The
other end of the power cord should be connected to
a suitable wall outlet.
DIGITAL COAXIAL IN 1, 2, and 3
These coaxial digital audio inputs are for connect-
ing components with coaxial digital audio outputs,
such as CD and DVD players. They’re assignable,
which means you can assign each one to an input
selector to suit your setup. See “Digital Input
Setup” on page 44.
DIGITAL OPTICAL IN 1 and 2
These optical digital audio inputs are for connecting
components with optical digital audio outputs, such
as CD and DVD players. They’re assignable, which
means you can assign each one to an input selector
to suit your setup. See “Digital Input Setup” on
page 44.
GND screw
This screw is for connecting a turntable’s ground
wire.
TUNER IN (TX-SA706 only)
This analog audio input is for connecting a tuner’s
analog audio output.
CD IN
This analog audio input is for connecting a CD
player’s analog audio output.
TAPE IN/OUT
This analog audio input and output are for connect-
ing a recorder with an analog audio input and output
(cassette, Mini Disc, etc.).
GAME/TV IN
Here you can connect a game console, TV, etc.
Input jacks include S-Video, composite video, and
analog audio.
CBL/SAT IN
Here you can connect a cable/satellite receiver, set-
top box, etc. Input jacks include S-Video, composite
video, and analog audio.