Sylvania SREC427 - Manual (Page 60)

60
Suggestions for Timer Recording
• If there is a power failure or this unit has been unplugged for more than 3 seconds, the clock setting and all timer settings will be lost.
• If a disc is not on the tray, timer recording cannot be performed. Please insert a recordable disc.
• If a tape with a record tab is not in the cassette compartment, timer recording cannot be performed. Please insert a recordable tape.
See "Accidental erasure prevention" on page 28.
• The main unit automatically ejects a tape without a record tab inserted in the compartment when you turn off the power and move to
timer standby mode.
• When all the timer recording is completed, the RECORD indicator disappears. To play the recorded disc (or the tape), press POWER
button first and then press PLAY B (DVD) or PLAY B (VCR). To eject the recorded disc (or the tape), press A OPEN/CLOSE (or C
STOP/A EJECT) button.
• The timer recording is not performed in DVD and VCR at the same time. If you set two programs with the same channel and time both
in DVD and VCR, the program that has priority will be recorded.
• During timer recording or timer standby (RECORD indicator is on the front display), any operations on the unit will not be available. To
make these operations available, cancel the timer recording or timer standby first (RECORD indicator disappears).
• To cancel the timer standby mode, press POWER button.
• When the Start and the End time are the same, the length of the recording will be set for 24 hours. When the disc reaches at the end
during the recording, the unit turns itself off.
• When the programmed Start and End time are earlier than the current time, the recording will be set on the same date in the next year.
• If your programmed Start time for DVD recording is within 2 minutes from the current time, the power will turn on for recording standby
right after you turn the power off. For a videotape recording, the power will turn on shortly before the Start time.
• If a videotape ends during timer recording, the unit will stop, eject the videotape, and turn itself off.
• When two or more programmings are overlapped, "Overlap" will be displayed.
This unit records the programs according to priority if the timer programs are overlapped. The timer program set first is given priority.
A timer recording of lower priority will be canceled, begin from the middle or stopped at the end.
Check the overlapped timer programs and change the priority if necessary.
The priority of overlapped settings
TIMER RECORDING
OPERATING DVD RECORDER
Example:
When the end time of the programming currently
being recorded and the starting time of the one to be recorded
sequentially are same:
PROG. A
PROG. B
Actual
recording
The first 20-90 seconds will be cut off.
PROG. B PROG. A
PROG. A
PROG. B
Actual
recording
PROG. B
When the recording time is entirely overlapped:
PROG. A will not be recorded.
PROG. A
PROG. B
Actual
recording
PROG. B PROG. A
When the recording time is partially overlapped:
PROG. A will start after PROG. B is complete to be recorded.
A programming set previously has priority
When the starting time is the same:
A program set previously (PROG.A) has priority.
PROG. A
PROG. B
Actual
recording
PROG. A PROG. B
PROG. C
ex. 2
When some programming have been
made at the end time of the
programming currently being recorded:
A program set previously (PROG. B) has priority.
PROG. A
ex.1
PROG. B
Actual
recording
PROG. A PROG. B
Note for DVD timer recording
• When the recording time
of two programs are over-
lapped, or the End time of
a program and the Start
time of another is the
same, the first 20-90 sec-
onds of the subsequent
program will be cut off.
T2020UA_45-LAST 04.8.10 3:41 PM Page 60