2 equipment warning labels, Danger, 32° ambient temperature – Toshiba AUXILIARY CABINET 431M User Manual

Page 40: Warning, Figure 11-2: battery cabinet warning labels, Avertissement, Warning - risk of electric shock, Wa r n in g, Hazardous voltages

Advertising
background image

32

4300 Series Ancillary Cabinets Installation and Operation Manual

11.2 EQUIPMENT WARNING LABELS

DO NOT attempt to install, operate, maintain or dispose of this equipment until you have read and under-

stood all of the product warnings and user directions that are contained in this instruction manual.
FIgure 11-2 shows examples of warning labels that may be found attached to the equipment. DO NOT

remove or cover any of the labels. If the labels are damaged or if additional labels are required, contact

your TOSHIBA representative for additional labels.
The following are examples of the warning labels that may be found on the equipment. The labels are

there to provide useful information or to indicate an imminently hazardous situation that may result in seri-

ous injury, severe property and equipment damage, or death if the instructions are not followed.

(A)

40308

(B)

41750

(D)

49455

(C) 43784

(F)

66005

(E) 48082

Figure 11-2: Battery Cabinet Warning Labels

EN CAS D UTILISATION EN ATMOSPHERE CONTROLEE.

'

AVERTISSEMENT

CONSULTER LA NOTICE TECHNIQUE.

WARNING - Risk of electric shock

DO NOT REMOVE COVER. NO USER SERVICEABLE PARTS

INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
HAZARDOUS LIVE PARTS INSIDE THIS UPS ARE ENERGIZED

FROM THE BATTERY SUPPLY EVEN WHEN THE INPUT AC POWER

IS DISCONNECTED.
CAPACITORS STORE HAZARDOUS ENERGY. DO NOT REMOVE

COVER UNTIL 5 MINUTES AFTER DISCONNECTING ALL SOURCES

OF SUPPLY.

BATTERY BACK-UP TIME, WHICH WAS FACTORY-SET AT A

PREDETERMINED LEVEL, DECREASES GRADUALLY BETWEEN

SERVICE PERIODS. THE BATTERIES SHOULD BE REPLACED

EVERY THREE YEARS AFTER THE LAST SERVICING, THE DATE

OF WHICH IS WRITTEN ON THE ID PLATE LOCATED ON THE

REAR SIDE OF THE UPS UNIT, OR IN THE BOX BELOW.
DATE OF LAST BATTERY CHARGE:

PN 41750

4.00

4.00

PRINT - BLACK

MATERIAL - UL APPROVED - 3M 7883

ADHESIVE - UL APPROVED - 3M 300

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, INSTALL

IN A TEMPERATURE AND HUMIDITY CONTROLLED INDOOR

AREA FREE OF CONDUCTIVE CONTAMINANTS.

THIS MATERIAL IS THE EXCLUSIVE PROPERTY OF TOSHIBA INTERNATIONAL

CORPORATION AND SHALL NOT BE REPRODUCED, USED, OR DISCLOSED

TO OTHERS UNLESS PRIOR WRITTEN AUTHORIZATION IS OBTAINED.

TITLE:

SCALE:

DRAWING NO.:

ECN

DATE

BY

DRAWN:

CHECKED:

APPROVED:

CAUTION LABEL

10-18KVA UPS

41750

3=2

TF 9-8-94

REV:

1

13131 WEST LITTLE YORK ROAD, HOUSTON, TX 77041 U.S.A.

ECO 77296 07-09 ZIR

AMB 07-09 AMB 07-09

DANGER

DC VOLTAGE

DC Voltage supplied by batteries is still

present after equipment has been

turned off and taken off line.

Accidental contact with live parts can

cause personal injury and death.

Disconnect all DC Sources before

performing any service or testing

in this compartment.

MATERIAL - VINYL OR POLYESTER

TEMPERATURE - MINUS 20 TO 100 deg. C

ADHESIVE - V23 OR EQUIV.

MUST RESIST OIL SOLVENTS

ALL MATERIALS USED MUST

BE UL RECOGNIZED

WARNING AREA BACKGROUND COLOR: ANSI DANGER RED

WARNING AREA TEXT COLOR: ANSI WHITE

TEXT AREA BACKGROUND COLOR: ANSI WHITE

TEXT AREA TEXT COLOR: ANSI BLACK

CORNER RADIUS: VENDOR STANDARD

0.00

WARNING AREA
TEXT AREA

0.

00

3.

00

1.50

43784

THIS MATERIAL IS THE EXCLUSIVE PROPERTY OF TOSHIBA INTERNATIONAL

CORPORATION AND SHALL NOT BE REPRODUCED, USED, OR DISCLOSED

TO OTHERS UNLESS PRIOR WRITTEN AUTHORIZATION IS OBTAINED.

TITLE:

SCALE:

DRAWING NO.:

ECN

DATE

BY

DRAWN:

CHECKED:

APPROVED:

DANGER LABEL

DC VOLTAGE

43784

FULL

RCM 4-11-96

REV:

0

13131 WEST LITTLE YORK ROAD, HOUSTON, TX 77041 U.S.A.

TF 6-1-07

TF 6-1-07

UNLESS PRIOR WRITTEN AUTHORIZATION IS OBTAINED.

THIS MATERIAL IS THE EXCLUSIVE PROPERTY OF

BE REPRODUCED, USED OR DISCLOSED TO OTHERS

TOSHIBA INTERNATIONAL CORPORATION AND SHALL NOT

APPROVED BY

DATE

CHECKED BY

DRAWN BY:

DATE

DATE

DRAWING NO.

13131 WEST LITTLE YORK ROAD, HOUSTON, TX, 77041 U.S.A.

TITLE:

SCALE

OF

SH.

ORDER NO.

TOSHIBA INTERNATIONAL CORPORATION

TOSHIBA INTERNATIONAL CORPORATION

ECN# 63201

12-99

BC

1"=1"

1

1

49455

DISK: PRT

REV: 2

BC

12-8-99

E3 2.4-8kVA UPS WARNING LABEL SHEET

MATERIAL - POLYESTER

TEMPERATURE - MINUS 20 TO 100 deg. C

ADHESIVE - V23 OR EQUIV.

MUST RESIST OIL SOLVENTS

ALL MATERIALS USED MUST

BE UL RECOGNIZED

WARNING AREA BACKGROUND COLOR: ANSI WARNING ORANGE

WARNING AREA TEXT COLOR: ANSI BLACK

TEXT AREA BACKGROUND COLOR: ANSI WHITE

TEXT AREA TEXT COLOR: ANSI BLACK

----- INDICATES KISS CUT

WARNING

This unit contains sealed lead acid batteries.

Lack of preventative maintenance could result

in batteries exploding and emitting gasses and/or

flame. Annual preventative maintenance must be

performed by an authorized, trained technician.

CRITICAL FUSE SIZING

Incorrect fuse replacement size

may result in fire or inadequate

equipment protection.

Replace only with same type

and rating of fuse.

WARNING

WARNING

This unit contains sealed lead acid batteries.

Lack of preventative maintenance could result

in batteries exploding and emitting gasses and/or

flame. Annual preventative maintenance must be

performed by an authorized, trained technician.

WARNING

This unit contains sealed lead acid batteries.

Lack of preventative maintenance could result

in batteries exploding and emitting gasses and/or

flame. Annual preventative maintenance must be

performed by an authorized, trained technician.

WARNING

This unit contains sealed lead acid batteries.

Lack of preventative maintenance could result

in batteries exploding and emitting gasses and/or

flame. Annual preventative maintenance must be

performed by an authorized, trained technician.

WARNING

This unit contains sealed lead acid batteries.

Lack of preventative maintenance could result

in batteries exploding and emitting gasses and/or

flame. Annual preventative maintenance must be

performed by an authorized, trained technician.

WARNING

This unit contains sealed lead acid batteries.

Lack of preventative maintenance could result

in batteries exploding and emitting gasses and/or

flame. Annual preventative maintenance must be

performed by an authorized, trained technician.

WARNING

This unit contains sealed lead acid batteries.

Lack of preventative maintenance could result

in batteries exploding and emitting gasses and/or

flame. Annual preventative maintenance must be

performed by an authorized, trained technician.

WARNING

This unit contains sealed lead acid batteries.

Lack of preventative maintenance could result

in batteries exploding and emitting gasses and/or

flame. Annual preventative maintenance must be

performed by an authorized, trained technician.

WARNING

This unit contains sealed lead acid batteries.

Lack of preventative maintenance could result

in batteries exploding and emitting gasses and/or

flame. Annual preventative maintenance must be

performed by an authorized, trained technician.

WARNING

This unit contains sealed lead acid batteries.

Lack of preventative maintenance could result

in batteries exploding and emitting gasses and/or

flame. Annual preventative maintenance must be

performed by an authorized, trained technician.

WARNING

This unit contains sealed lead acid batteries.

Lack of preventative maintenance could result

in batteries exploding and emitting gasses and/or

flame. Annual preventative maintenance must be

performed by an authorized, trained technician.

WARNING

This unit contains sealed lead acid batteries.

Lack of preventative maintenance could result

in batteries exploding and emitting gasses and/or

flame. Annual preventative maintenance must be

performed by an authorized, trained technician.

WARNING

WARNING

WARNING

WARNING

WARNING

WARNING

CRITICAL FUSE SIZING

Incorrect fuse replacement size

may result in fire or inadequate

equipment protection.

Replace only with same type

and rating of fuse.

CRITICAL FUSE SIZING

Incorrect fuse replacement size

may result in fire or inadequate

equipment protection.

Replace only with same type

and rating of fuse.

CRITICAL FUSE SIZING

Incorrect fuse replacement size

may result in fire or inadequate

equipment protection.

Replace only with same type

and rating of fuse.

CRITICAL FUSE SIZING

Incorrect fuse replacement size

may result in fire or inadequate

equipment protection.

Replace only with same type

and rating of fuse.

CRITICAL FUSE SIZING

Incorrect fuse replacement size

may result in fire or inadequate

equipment protection.

Replace only with same type

and rating of fuse.

CRITICAL FUSE SIZING

Incorrect fuse replacement size

may result in fire or inadequate

equipment protection.

Replace only with same type

and rating of fuse.

8.

12

"

C

R

IT

IC

A

L

FU

SE

S

IZ

IN

G

In

co

rre

ct

fu

se

re

pl

ac

em

en

t s

iz

e

m

ay

re

su

lt

in

fi

re

o

r i

na

de

qu

at

e

eq

ui

pm

en

t p

ro

te

ct

io

n.

R

ep

la

ce

o

nl

y

w

ith

s

am

e

ty

pe

an

d

ra

tin

g

of

fu

se

.

W

A

R

N

IN

G

C

R

IT

IC

A

L

FU

SE

S

IZ

IN

G

In

co

rre

ct

fu

se

re

pl

ac

em

en

t s

iz

e

m

ay

re

su

lt

in

fi

re

o

r i

na

de

qu

at

e

eq

ui

pm

en

t p

ro

te

ct

io

n.

R

ep

la

ce

o

nl

y

w

ith

s

am

e

ty

pe

an

d

ra

tin

g

of

fu

se

.

W

A

R

N

IN

G

C

R

IT

IC

A

L

FU

SE

S

IZ

IN

G

In

co

rre

ct

fu

se

re

pl

ac

em

en

t s

iz

e

m

ay

re

su

lt

in

fi

re

o

r i

na

de

qu

at

e

eq

ui

pm

en

t p

ro

te

ct

io

n.

R

ep

la

ce

o

nl

y

w

ith

s

am

e

ty

pe

an

d

ra

tin

g

of

fu

se

.

W

A

R

N

IN

G

10.40"

ECO 73600

04-07 AMB

MUST BE RoHS COMPLIANT

TF

5-3-07

TF

5-3-07

WARNING AREA

TEXT AREA

DANGER

Hazardous voltages are used in the operation
of this equipment and could cause severe personal
injury or loss of life.
The following precautions should be observed to
reduce the risk of injury or death.

HAZARDOUS VOLTAGES

Only qualified technicians familiar with this equipment and the
information supplied with it should be permitted to install and
operate this equipment.
Installation of electrical equipment must be done in
accordance with National Electrical Code and any other state
or local codes. Proper grounding and conductor sizing must
be installed for safe operation.

During operation, keep all covers in place and cabinet
doors shut.

When performing visual inspections and maintenance, if
possible, be sure the MBS is turned off and the incoming
AC feed is turned off and locked out.

If it is necessary to make measurements with the power
on, do not touch any electrical connection points. Remove
all jewelry from wrists and fingers. Make sure test equipment
is in good, safe operating condition.

While servicing, stand on some type of insulation, and be
sure not to be grounded.

Follow the safety instructions given in the equipment manual
carefully and observe all danger, warning and caution notices.

64818

MATERIAL - VINYL OR POLYESTER
TEMPERATURE - MINUS 20 TO 100 deg. C
ADHESIVE - V23 OR EQUIV.
MUST RESIST OIL SOLVENTS
ALL MATERIALS USED MUST
BE UL RECOGNIZED

WARNING AREA BACKGROUND COLOR: ANSI DANGER RED
WARNING AREA TEXT COLOR: ANSI WHITE
TEXT AREA BACKGROUND COLOR: ANSI WHITE
TEXT AREA TEXT COLOR: ANSI BLACK
CORNER RADIUS: VENDOR STANDARD

0.00

0.00

3.75

4.50

The UPS and Battery Cabinet will have hazardous
voltages present even after the AC feed is turned off.

THIS MATERIAL IS THE EXCLUSIVE PROPERTY OF TOSHIBA INTERNATIONAL
CORPORATION AND SHALL NOT BE REPRODUCED, USED, OR DISCLOSED
TO OTHERS UNLESS PRIOR WRITTEN AUTHORIZATION IS OBTAINED.

TITLE:

SCALE:

DRAWING NO.:

ECN

DATE

BY

DRAWN:

CHECKED:

APPROVED:

DANGER LABEL
GENERAL - MBS

64818

FULL

WLM 3-9-11

REV:

0

13131 WEST LITTLE YORK ROAD, HOUSTON, TX 77041 U.S.A.

WLM 3-10-11

ZIR 3-10-11

40308

DANGER

AC VOLTAGE

This UPS receives power from more

than one source. Disconnect all AC

sources before performing any service

or testing inside this unit

MATERIAL - VINYL OR POLYESTER

TEMPERATURE - MINUS 20 TO 100 deg. C

ADHESIVE - V23 OR EQUIV.

MUST RESIST OIL SOLVENTS

ALL MATERIALS USED MUST

BE UL RECOGNIZED

WARNING AREA BACKGROUND COLOR: ANSI DANGER RED

WARNING AREA TEXT COLOR: ANSI WHITE

TEXT AREA BACKGROUND COLOR: ANSI WHITE

TEXT AREA TEXT COLOR: ANSI BLACK

CORNER RADIUS: VENDOR STANDARD

0.00

WARNING AREA
TEXT AREA

0.

00

3.

00

1.50

48082

THIS MATERIAL IS THE EXCLUSIVE PROPERTY OF TOSHIBA INTERNATIONAL

CORPORATION AND SHALL NOT BE REPRODUCED, USED, OR DISCLOSED

TO OTHERS UNLESS PRIOR WRITTEN AUTHORIZATION IS OBTAINED.

TITLE:

SCALE:

DRAWING NO.:

ECN

DATE

BY

DRAWN:

CHECKED:

APPROVED:

DANGER LABEL

MULTIPLE SOURCES

48082

FULL

BC 6-10-98

REV:

0

13131 WEST LITTLE YORK ROAD, HOUSTON, TX 77041 U.S.A.

TF 8-2-06

TF 8-2-06

32° AMBIENT

TEMPERATURE

0.50"

1.00"

THIS MATERIAL IS THE EXCLUSIVE PROPERTY OF TOSHIBA INTERNATIONAL
CORPORATION AND SHALL NOT BE REPRODUCED, USED, OR DISCLOSED
TO OTHERS UNLESS PRIOR WRITTEN AUTHORIZATION IS OBTAINED.

TITLE:

SCALE:

DRAWING NO.:

ECN

DATE

BY

DRAWN:

CHECKED:

APPROVED:

LABEL AMBIENT
32 C 4310 BC

°

66005

2=1

WLM 8-08-11

REV:

0

13131 WEST LITTLE YORK ROAD, HOUSTON, TX 77041 U.S.A.

PRINT: BLACK
UL RECOGNIZED MATERIAL: 2-3 MIL MATTE METALLIC POLYESTER
UL RECOGNIZED ADHESIVE: 3M 300 SERIES OR EQUIV..

ZIR 8-08-11

WLM 8-08-11

Advertising
This manual is related to the following products: