Tunturi C35 User Manual

Page 7

Advertising
background image

G B

7

O W N E R ' S M A N U A L

C 3 5

REMARKS ON TELEMETRIC MEASUREMENT

If the electrode surfaces are not moist, the heart rate
reading will not appear on the display. If the electrodes
are dry, they must be moistened again. Allow the
electrodes to warm up properly to ensure accurate
heart rate measurement. If there are several telemetric
heart rate measurement equipments next to each
other, the distance between them should be at least 1.5
m. Similarly, if there is only one receiver and several
transmitters in use, only one person with a transmitter
should be within transmission range. The transmitter is
switched to an active state only when it is being used for
measurement. Sweat and other moisture can, however,
keep the transmitter in an active state and waste battery
energy. Therefore it is important to dry the electrodes
carefully after use.

When selecting training attire, please note that some
fibers used in clothes (e.g. polyester, polyamide) create
static electricity, which may prevent reliable heart rate
measurement.

Please note that a mobile phone, television and other
electrical appliances form an electro-magnetic field
around them, which will cause problems in heart rate
measurement.

CONSOLE

KEYS

1. SET

Selection of the goal values

2. RESET.

Zeroing the exercising values, ending the exercise and
return into main display

3. ”+ / -”

Setting the goal values, increasing the intensity (+),
decreasing the intensity (-)

4. RECOVERY

Measuring the recovery heart rate

5. START/STOP

Starting and interrupting the exercise.

DISPLAY

1. PERFORMANCE SPEED (/MIN)

Pedalling speed (RPM). The column underneath also
shows the pedalling speed.

2. EXERCISE DURATION

00:00-99:59; measuring at 1 second intervals, h1:40-h9:
59 measuring at 1 minute intervals.

3. HEART RATE DURING EXERCISE

The symbol of a heart blinks simultaneously with your
own heart rate during the exercise. The arrow signs show
if the heart rate exceeds or surpasses the set values.

4. EXERCISE TRIP LENGTH (KM/MILE)

O0.0 – 99.99 km / miles

5. EXERCISE SPEED (KMH/MPH)

00.0-99.9 kmh / mph

6. ENERGY CONSUMPTION (KCAL)

Estimated total energy consumption during the exercise,
0 –9999 kcal

7. CLOCK (CLOCK)

Real time clock

8. THERMOMETER (TEMP C / TEMP F)

Measures the room temperature either in Celsius or
Fahrenheit

9. HYGROMETER (HUMIDITY %)

Measures the room humidity, 0-100%.

10. DISPLAY OF THE CHOSEN FUNCTION

The console displays the chosen exercise mode (Program
= preprogrammed program; Manual = manually
programmed exercise; Recovery = measuring of recovery
heart rate, Target HR = heart rate exercise; Min Max =
upper and lower heart rate limits)

11. DISPLAY OF AN EXERCISE PROFILE

The profile of a preprogrammed exercise program.

12. DISPLAY OF THE CUMULATIVE HEART RATE

If the heart rate is measured during the exercise, the
display shows the profile of the heart rate formed during
the exercise.

13. CHANGE OF BATTERIES (BATTERY LOW)

A warning sign is displayed before the change of
batteries.

USING THE CONSOLE

The console is turned on by pressing any key. It
the device has not been used for five minuts, it
automatically switches itself to main display.

Select the desired measuring unit with the switch behind
the console. You can select either metric (km, km/h,
Celsius) or English (miles, mph, Fahrenheit) units.

Set the clock in the console (Clock) as follows: In main
display, press both of the arrow keys simultaneously for
three seconds. The clock is shown in the main number
display. Set the right time using the arrow keys; switch
from hours to minutes and back to main display by
pressing the SET key.

MANUAL EXERCISE

In a manual exercise you can adjust the resistance during
the exercise by the ”+/-” keys.

1.

You can start exercising immediately by pressing the

START/STOP key. Adjust the resistance by pressing the
”+/-” keys.

2.

You can start exercising by setting goal values. Press an

”+/-” key until under the main number display is shown
the text ”Manual”.

3.

Press the SET key after which you can set the goal

values.

Tunturi_C35 7

7.1.2005, 15:24:43

Advertising