Watlow Electric Integrated Controller User Manual Rev C EZ-ZONE PM - Manual (Page 30)

Wa t l o w E Z - Z O N E
®
P M I n t e g r a t e d C o n t r o l l e r • 2 8 • C h a p t e r 5 O p e r a t i o n s P a g e
5
Chapter 5: Operations Page
To go to the Operations Page from the Home Page,
press both the Up
¿ and Down ¯ keys for three sec-
onds. [``Ai] will appear in the upper display and
[oPEr] will appear in the lower display.
• Press the Up ¿ or Down ¯ key to move through
the menus.
• Press the Advance Key ‰ to move to a submenu.
• Press the Up ¿ or Down ¯ key to move through
the submenus.
• Press the Advance Key ‰ to move through the pa-
rameters of the menu or submenu.
• Press the Infinity Key ˆ to move backwards
through the levels: parameter to submenu; sub-
menu to menu; menu to Home Page.
• Press and hold the Infinity Key ˆ for two seconds
to return to the Home Page.
Note: Avoid continuous writes within loops. Excessive writes to
EEPROM will cause premature EEPROM failure. The EEPROM is
rated for 1,000,000 writes.
Home
Page
Operations Page Parameters
[~~p~] ň
[~~Sp] <>Æ
[``Ai] ň
[oPEr] ‰Æ
[~~~I] ň
[``Ai] ‰Ж
И
[`ain] ‰Æ [`i;Er] ‰Ж
З
[`i;Ca] ‰
Hold both keys
for 3 seconds.
Analog
Input Menu
<З
И>
Input 1
Submenu
<З
И>
Process
Value Input Error
Status Input
Calibration
Offset
Ɉ Input 2
Submenu
Same as above.
Ɉ [`diO] ň
[oPEr] ‰Æ
[~~~5] ň
[`diO] ‰Ж
И
[`do;S] ‰Ж
З
[`Ei;S] ‰
Digital In-
put/Output
Menu
<З
И>
Digital I/O 5
Submenu
<З
И>
Output State Event Input
Status
Ɉ Digital I/O 6
Submenu
Same as above.
Ɉ [LiM] ň
[oPEr] ‰Ж
И
[`LL;S] ‰Ж
З
[`Lh;S] ‰
Limit
Menu
<З
И>
Limit Low
Set Point Limit High
Set Point
Ɉ [Mon] ň
[oPEr] ‰Ж
И
[C;MA] ‰Æ [`h;Pr] ‰Æ [`C;Pr] ‰Æ

[`C;SP] ‰Ж
З
[`Pu;A] ‰
Monitor
Menu
<З
И>
Control
Mode Active Heat Power Cool Power Closed Loop
Working Set
Point Process
Value Active
Ɉ [Loop] ň
[oPEr] ‰Ж
И
[`r;En] ‰Æ [`r;tY] ‰Æ [`C;M] ‰Æ [A;tSP] ‰Æ [`AUt] ‰Æ [`C;SP] ‰Æ [`id;S] ‰Æ [`h;Pb] ‰Æ [`h;hY] ‰Æ [`C;Pb] ‰Æ [`C;hy] ‰Æ [``ti] ‰Æ [``td] ‰Æ [``db] ‰Ж
З
[`o;SP] ‰
Loop Menu
<З
И>
Remote
Enable Remote Set
Point Type Control
Mode Autotune
Set Point Autotune
Request Closed Loop
Set Point Idle Set
Point Heat Propor-
tional Band Heat Hyster-
esis Cool Propor-
tional Band Cool Hyster-
esis Time Integral Time Deriva-
tive
Dead Band Open Loop
Set Point
Ɉ [ALM] ň
[oPEr] ‰Æ
[~~~I] ň
[ALM] ‰Ж
И
[`A;Lo] ‰Ж
З
[`A;hi] ‰
Alarm
Menu
<З
И>
Alarm 1
Submenu
<З
И>
Alarm Low
Set Point Alarm High
Set Point
Ɉ Alarm 2 to 4
Submenus
Same as above.
Ɉ [CUrr] ň
[oPEr] ‰Ж
И
[`C;hi] ‰Æ

[`C;Lo] ‰Æ

[`CU;r] ‰Æ

[`C;Er] ‰Ж
З
[`h;er] ‰
Current
Menu
<З
И>
Current High
Set Point Current Low
Set Point Current Read Current Error Heater Error
Ɉ
[P;StA] ň
[oPEr] ‰Ж
И
[P;Str] ‰Æ [P;ACr] ‰Æ [`Stp] ‰Æ [S;tYP] ‰Æ [tg;SP] ‰Æ [AC;SP] ‰Æ [`S;ti] ‰Æ [Ent1] ‰Ж
З
[``JC] ‰
Profi le
Status
Menu
<З
И>
Profi le Start Profi le
Action
Request Active Step Active Step
Type Active Target
Set Point Active Set
Point Step Time
Remaining Active Event
Output
(1 or 2) Jump Count
Remaining
Note:
Some of these menus and parameters may not appear, depending
on the controller's options. See model number information in the
Appendix for more information.
If there is only one instance of a menu, no submenus will appear.
Navigating the Operations Page