Yamaha RX-Z7 - Manual (Page 101)

101
En
Graphical user interface (GUI) menu
AD
V
ANCED
OPERA
T
ION
Mosquito NR (Mosquito noise reduction)
Mosquito noise is a type of noise that appears along
edges of compression artifacts. Use this feature to
adjust the mosquito noise reduction level.
Choices: Off, Low, Medium, High
Block NR (Block noise reduction)
Block noise is often caused when the bitrate is too
low to accurately encode the video. Use this feature
to adjust the block noise reduction level.
Control range: 0 to 50
Detail Enhancement (Detail enhancement)
Use this feature to adjust finesses of images.
Control range: 0 to 50
Edge Enhancement (Edge enhancement)
Use this feature to adjust sharpness of images.
Control range: 0 to 50
Brightness (Brightness)
Use this feature to adjust brightness of images.
Control range: -50 to 50
Initial setting: 0
Contrast (Contrast)
Use this feature to adjust contrast of images.
Control range: -50 to 50
Initial setting: 0
Saturation (Saturation)
Use this feature to adjust saturation of images.
Control range: -50 to 50
Initial setting: 0
Use this feature to set the HDMI functions or check the
information about the video monitors connected to the
HDMI OUT jacks.
■ Standby Through (Standby through)
Mode (Standby through mode)
Use this feature whether this unit allows the HDMI signals
input at the HDMI IN jacks to pass thorough this unit
when this unit is in the standby mode. You can also
designate an HDMI IN jack and HDMI OUT jack(s) that
accept the signals when “Mode” is set to “Fix” and this
unit is in the standby mode.
When “Mode” is set to “Last” or “Fix”, the amount of power
consumption in the standby mode increases.
Input (HDMI IN jack select)
Use this feature to select an HDMI IN jack that accepts
HDMI signals when this unit is in the standby mode.
This setting is available only when “Mode” is set to “Fix”.
Output (HDMI OUT jack select)
Use this feature to select HDMI OUT jack(s) that output
HDMI signals when this unit is in the standby mode.
This setting is available only when “Mode” is set to “Fix”.
■ Audio Output (HDMI audio output)
Use this feature to select whether to play back HDMI
audio signals on this unit or on another HDMI component
connected to the HDMI OUT jacks on the rear panel of
this unit.
y
If “Audio Output” is set to “TV” or “Amp + TV”, available
audio signals vary depending on the specification of the
connected video monitor.
Setup (HDMI)
Choice Functions
Off Disables the HDMI standby through feature.
HDMI signals do not pass through this unit if
this unit is in the standby mode.
Last HDMI signals pass through this unit (only from
the HDMI IN jack to the HDMI OUT jack(s)
used when this unit is set to the standby mode)
even when this unit is in the standby mode.
Fix HDMI signals pass through this unit (from the
HDMI IN jack specified in “Input” to the HDMI
OUT jack(s) specified in “Output”) even when
this unit is in the standby mode.
Note
Note
Choice HDMI IN jack
IN1 HDMI IN1 (BD/HD DVD) jack
IN2 HDMI IN2 (DVD) jack
IN3 HDMI IN3 (CBL/SAT) jack
IN4 HDMI IN4 (DVR) jack
Front HDMI IN (VIDEO AUX) jack
Note
Choice HDMI IN jack
OUT1 + 2 HDMI OUT 1 and HDMI OUT 2 jacks
OUT1 HDMI OUT 1 jack
OUT2 HDMI OUT 2 jack
Choice Functions
Amp Outputs HDMI audio signals at the speakers
connected to this unit.
TV Outputs HDMI audio signals at the speakers of
the TV connected to this unit. The speakers
connected to this unit are muted.
Amp + TV Outputs HDMI audio signals at the speakers
connected to this unit and speakers of the TV
connected to this unit.
Choice Functions