GE Industrial Solutions AF-300 P11 - Manual (Page 54)

5-1
5. Function Selection
5.1 Function Selection List
F: Fundamental Functions
Func. Unit Min. Factory Setting Data Change
No. 30 HP 40 HP Formst during op
F00 Data protection F00 DATA PRTC 0, 1 - - 0 1 N
F01 Frequency command 1 F01 FREQ CMD 1 0 to 11 - - 0 1 N
F02 Operation method F02 OPR METHOD 0 to 4 - - 0 1 N
F03 Maximum frequency 1 F03 MAX Hz-1 50 to 120Hz Hz 1 60 1 N
F04 Base frequency 1 F04 BASE Hz-1 25 to 120Hz Hz 1 60 1 N
F05 Rated voltage 1 F05 RATED V-1 0V: (Output voltage V 1 230: (230V class) 1
(at Base frequency 1) proportional to source voltage) 460: (460V class)
230V class: 80 to 240V
460V class: 320 to 480V
F06 Maximum voltage 1 F06 MAX V-1 230V class: 80 to 240V V 1 230: (230V class) 1
(at Maximum frequency 1) 460V class: 320 to 480V 460: (460V class)
F07 Acceleration time 1 F07 ACC TIME1 0.01 to 3600 s s 0.01 6.0 20.0 12
F08 Deceleration time 1 F08 DEC TIME1
F09 Torque boost 1 F09 TRQ BOOST1 0.0, 0.1 to 20.0 - 0.1 2.0 12 Y
F10 Electronic (Select) F10 ELCTRN OL1 0, 1, 2 - - 1 3 Y
F11 Thermal 1 (level) F11 OL LEVEL1 20 to 135% of drive rated current A 0.01 Motor rated current 1 Y
F12 (time constant) F12 TIME CNST1 0.5 to 75.0 min min 0.1 5.0 10.0 19 Y
F13 Electronic thermal overload F13 DBR OL [ Up to 15 HP ] - - 3
relay (for braking resistor) 0, 1, 2 1
[ 20 HP and above ]
0
F14 Restart mode after F14 RESTART 0 to 5 - - 1
momentary power failure
F15 Frequency (high) F15 H LIMITER 0 to 120 Hz Hz 1 70 1 Y
F16 Limiter (low) F16 L LIMITER 0 1 N
F17 Gain (for frequency set signal) F17 FREQ GAIN 0.0 to 200.0% % 0.1 100.0 1 Y
F18 Bias frequency F18 FREQ BIAS -120.0 to +120.0 Hz Hz 0.1 0.0 1 Y
F20 DC brake (starting frequency) F20 DC BRK Hz 0.0 to 60.0 Hz Hz 0.1 0.0 3
F21 (braking level) F21 DC BRK LVL 0 to 80% % 1 0 1
F22 (braking time) F22 DC BRK t 0.0s (inactive) s 0.1 0.0 3
F23 Starting frequency F23 START Hz 0.1 to 60.0 Hz Hz 0.1 0.5 3
F24 (holding time) F24 HOLDING t 0.0 to 10.0 s s 0.1 0.0 3
F25 Stop frequency F25 STOP Hz 0.1 to 6.0 Hz Hz 0.1 0.2 1
F26 Motor sound (carrier freq.) F26 MTR SOUND 0.75 to 15 kHz (6kHz) kHz 1 2 1 Y
F27 (sound tone) F27 SOUND TONE 0 to 3 - - 0 1 Y
F30 FMA (voltage adjust) F30 FMA V-ADJ 0 to 200% % 1 100 1 Y
F31 (function) F31 FMA FUNC 0 to 10 - - 0 1 Y
F33 FMP (pulse rate) F33 FMP PULSES 300 to 6000 p/s (full scale) p/s 1 1440 1 Y
F34 (voltage adjust) F34 FMP V-ADJ 0%, 1 to 200% % 1 0 1 Y
F35 (function) F35 FMP FUNC 0 to 10 - - 0 1 Y
F36 30RY operation mode F36 30RY MODE 0, 1 - - 0 1 Y
F40 Torque limiter1 (driving) F40 DRV TRQ 1 20 to 150%, 999 % 1 999 1
F41 (braking) F41 BRK TRQ 1 0%, 20 to 150%, 999 999 1
5-17 F42 Torque vector control 1 F42 TRQVECTOR1 0, 1 - - 0 1 N
Name LCD Display Setting Range
Y
Y
Y
N
N
Y
N
N
0
0
5-7
5-10
5-11
Pg.
5-12
5-14
5-15
5-16