Asus Pundit P2-PE2 - Manual (Page 60)

5 - 1 2 5 - 1 2 5 - 1 2 5 - 1 2 5 - 1 2 C h a p t e r 5 : B I O S s e t u p C h a p t e r 5 : B I O S s e t u p C h a p t e r 5 : B I O S s e t u p C h a p t e r 5 : B I O S s e t u p C h a p t e r 5 : B I O S s e t u p
To clear the password:
1. Select either the S u p e r v i s o r P a s s w o r d S u p e r v i s o r P a s s w o r d S u p e r v i s o r P a s s w o r d S u p e r v i s o r P a s s w o r d S u p e r v i s o r P a s s w o r d or U s e r P a s s w o r d U s e r P a s s w o r d U s e r P a s s w o r d U s e r P a s s w o r d U s e r P a s s w o r d, then
press <Enter> twice. A P a s s w o r d D i s a b l e d ! P a s s w o r d D i s a b l e d ! P a s s w o r d D i s a b l e d ! P a s s w o r d D i s a b l e d ! P a s s w o r d D i s a b l e d ! message appears on
screen to indicate that the password has been cleared.
2. Press any key to continue. The password item value now shows
C l e a r .
C l e a r . C l e a r . C l e a r . C l e a r .
A n o t e a b o u t p a s s w o r d s A n o t e a b o u t p a s s w o r d s A n o t e a b o u t p a s s w o r d s A n o t e a b o u t p a s s w o r d s A n o t e a b o u t p a s s w o r d s
The BIOS Setup program allows you to specify passwords in the Boot
menu. These passwords control access to the BIOS during system
startup. The BIOS Setup program allows you to specify two different
passwords: a S u p e r v i s o r P a s s w o r d
S u p e r v i s o r P a s s w o r d S u p e r v i s o r P a s s w o r d S u p e r v i s o r P a s s w o r d S u p e r v i s o r P a s s w o r d and a U s e r P a s s w o r d U s e r P a s s w o r d U s e r P a s s w o r d U s e r P a s s w o r d U s e r P a s s w o r d. If you
did not set a Supervisor Password, anyone can access the BIOS Setup.
If you did, the Supervisor Password is required before entering the BIOS
Setup and gain full access to the configuration fields.
F o r g o t t h e p a s s w o r d ? F o r g o t t h e p a s s w o r d ? F o r g o t t h e p a s s w o r d ? F o r g o t t h e p a s s w o r d ? F o r g o t t h e p a s s w o r d ?
If you forget your password, you can clear it by erasing the CMOS Real
Time Clock (RTC) RAM. The RAM data containing the password
information is powered by the onboard button cell battery. If you need
to erase the CMOS RAM, refer to section “4.2 Jumper” for instructions.
Halt On [All Errors] Halt On [All Errors] Halt On [All Errors] Halt On [All Errors] Halt On [All Errors]
Specifies the type of error that will cause the system to halt.
Configuration options: [All Errors] [No Error] [All but Keyboard]
[All but Disk] [All but Disk/Keyboard]
Installed Memory [XXX MB] Installed Memory [XXX MB] Installed Memory [XXX MB] Installed Memory [XXX MB] Installed Memory [XXX MB]
Displays the amount of conventional memory auto-detected by the system
during the boot process.