LG 42LD6DDH - Manual (Page 104)

9 206-4190
1. Upon launching, the Express Script Installer Menu Wizard prompts you
to select a menu mode. Use the Up/Down arrow keys on the Installer
Remote to select the appropriate option:
• Select/highlight
Express Script in order to proceed with the Installer
Menu Wizard. Then, press OK (Enter) on the Installer Remote.
• Select/highlight Exit Express Script to exit the Installer Menu Wizard.
Then, press OK (Enter) on the Installer Remote.
The remaining steps of this procedure describe the Express Script
Installer Menu Wizard. Use the Installer Remote to make selections and
complete each step. You can select the Back button, where available, to
check previous settings, as necessary.
Caution: If you opt to exit the Express Script Installer Menu
Wizard at any time while it is in progress, any settings made
will not be retained.
2. Use the Left/Right arrow keys to select the appropriate tuning band
(Cable Standard [default], Cable HRC, Cable IRC, or Air). When you have
made your selection, use the arrow keys to select Next, and then press
OK (Enter).
3. Use the Up/Down arrow keys to select the desired Aux input option.
(Note: If you simply select Next and press OK (Enter) in this step, default
values will be used.)
• To customize settings, select
Customize Inputs and press OK (Enter).
Aux input options are displayed in a pop-up window. Use the arrow
keys to select the input(s) you want to enable or disable. When you are
finished, press MENU to close the pop-up window. Then, continue with
step 4.
• To use default values, select Use default values and press OK (Enter).
Then, continue with step 4.
4. If using the Zenith pillow speaker code (default), you can simply select
Next and press OK (Enter).
Otherwise, select the pillow speaker code field, and use the Left/Right
arrow keys to select the appropriate option. When you have made your
selection, use the arrow keys to select Next, and then press OK (Enter).
Express Script Installer Menu Wizard
The Express Script Installer Menu Wizard guides you through the process of setting up the essential items for
most hospital TV viewing applications and is displayed each time the TV is turned ON, unless it previously has
been completed or exited.
Note: If previously completed or exited, the Express Script Installer Menu Wizard also can be re-activated
from the Installer Menu—set Installer Menu item 117 FACT DEFAULT to 001 to initiate the Express Script
Installer Menu Wizard. See the “Installer Menu” section of this document for further information.
Note: If you plan to create a customized Master TV Setup using the procedure on pages 11 to 14, transfer
(Teach) a Master TV Setup to a Target TV, or configure a TV with an FTG device for FTG Mode of operation,
be sure to exit the Express Script in order to avoid setup conflicts that may cause the TV to malfunction.
Which menu mode will you be using?
Installer Menu Wizard
Select Menu Mode
OK PTC: V0.00.007 CPU: V03.30.00 ASIC: 20E7
Exit Express Script
Which tuning band would you like to use?
Installer Menu Wizard
Step 1. Tuning Band
OK Exit Express Script
Back Next
F Exit Script G
Cable Standard
PTC: V0.00.007 CPU: V03.30.00 ASIC: 20E7
2 1 4 5 6 3
►
►
► ► ► ► ► 7 ►
Installer Menu Wizard
OK Exit Express Script PTC: V0.00.007 CPU: V03.30.00 ASIC: 20E7
2 1 4 5 6 3 ► ► ► ► ► 7 ►
Which inputs will you be using?
Step 2. Aux Input
Customize Inputs.
Use default values.
Back Next
Up/Down/Left/Right arrow keys
Which brand pillow speaker code will you be using?
Installer Menu Wizard
Step 3. Pillow Speaker
OK Exit Express Script
Back Next
F Exit Script G
Zenith code
PTC: V0.00.007 CPU: V03.30.00 ASIC: 20E7
3 4 5 6 ► ► ► 7 ► 1 2 ► ►
►
►
(Continued on next page)
Express Script