Beijer Electronics AN-BEI-H2-038 - Manual (Page 8)

APPLICATION NOTE AN‐BEI‐H2‐038 Date: 15/02/12
AN‐BEI‐H2‐038 Modbus RTU Control and Register Mapping 8
Parameter Register
Number Description Range Scaling Type
P2‐18 218 User relay 2 output function select
0: Drive running
1: Drive healthy
2: Motor at target speed
3: Motor Speed > 0
4: Motor Speed > limit
5: Motor Current > limit
6: Motor Torque > limit
7: 2
nd Analog input > limit
U16
P2‐19 219 User relay 2 upper limit P2‐20 to 2000 1 = 0.1% U16
P2‐20 220 User relay 2 lower limit 0 to P2‐19 1 = 0.1% U16
P2‐21 221 Display scaling factor 0 to 30000 1 = 0.001 U16
P2‐22 222 Display scaling source
0: Motor Speed
1: Motor Current
2: 2
nd Analog input
U16
P2‐23 223 Zero Speed holding time 0 to 600 1 = 0.1 U16
P2‐24 224 Effective switching frequency
0 = 4kHz
1 = 8kHz
2 = 12kHz
3 = 16kHz
4 = 24kHz
5 = 32kHz U16
P2‐25 225 Fast deceleration ramp time 0 to 3000 1 = 0.1s U16
P2‐26 226 Spin start enable
0 : Disabled
1 : Enabled
1
U16
P2‐27 227 Standby mode 0 to 2500 1 = 0.1 U16
P2‐28 228 Slave speed scaling control
0: Disabled
1: Preset by slave speed scaling
2: P2‐33 scaling + analog in1 offset
3: P2‐33 scaling + analog in1 scaling U16
P2‐29 229 Slave Speed scaling factor ‐5000 to 5000 1 = 0.1 S16
P2‐30 230 Analog input 1 format
0 = 0‐10V
1 = 10‐0V
2 = ‐10‐10V,
3 = 0‐20mA,
4 = t 4‐20mA,
5 = r 4‐20mA,
6 = t 20‐4mA,
7 = r 20‐4mA U16
P2‐31 231 Analog input 1 scaling 0 to 5000 1 = 0.1 U16
P2‐32 232 Analog input 1 offset ‐5000 to 5000 1 = 0.1 S16
P2‐33 233 Analog input 2 format
0 = 0‐10V
1 = 10‐0V
2 = PTC Thermistor
3 = 0‐20mA,
4 = t 4‐20mA,
5 = r 4‐20mA,
6 = t 20‐4mA,
7 = r 20‐4mA U16
P2‐34 234 Analog input 2 scaling 0 to 5000 1 = 0.1 S16
P2‐35 235 Analog input 2 offset ‐5000 to 5000 1 = 0.1 U16
P2‐36 236 Start mode select
0 = Edge‐r
1 = Auto‐0
2 = Auto‐1
3 = Auto‐2
4 = Auto‐3
5 = Auto‐4
6 = Auto‐5 U16
P2‐37 237 Keypad restart speed
0: Minimum speed
1: Previous keypad speed
2: Current running Speed
3: Preset Speed 8 U16
P2‐38 238 Mains loss stop control
0: Mains loss ride through
1: Coast to Stop
2: Fast ramp to stop U16
P2‐39 239 Parameter Lock
0: Unlocked
1: Locked U16
P2‐40 240
Extended parameter access code
definition
0 ... 9 999
U16