Fagor 6H-755CX User Manual

Page 29

Advertising
background image

e n g l i s h

27

1

2

Installation

Using the oven

To fi nd out which model your oven is (“a”, “b”,
c”, “d”, “e”) compare its control panel with the
control panels shown in the illustrations.

1.1 Unpacking. Remove all the protective

packaging elements.

1.2 Mains connection. Always take into account

the data on the reference plate (1.2.1) and
the measurements of the cabinet the oven
will be housed in (1.2.2, 1.2.3).

The appliance must be connected to the
mains with a fi xed single-phase connection
with the neutral-to-neutral (blue) connection
guaranteed (1.2.4). Fit the oven into the
space and centre it (1.2.5). Make sure there
is no excess cable in the upper part (1.2.6).
Screw it to the fi tting using the two screws
supplied (1.2.7). The fi tted furniture or its
surface must be heat-resistant. The time
must be set in order to fi nish the installation.
After a period of inactivity, the machine
will turn to standby and its brightness
will diminish or the screen will switch off,
depending on the model.

0

Identifi cation

2.1 Setting the time. When you switch on the

oven, the display will fl ash (2.1.1, 2.1.2).
Adjust the time turning the

dial (2.1.3,

2.1.4). The time will automatically be
validated after 3 seconds, or if you press
either the

(2.1.5) or

button (2.1.6).

Note: The time will need to be reset if a
power cut occurs.

2.2 Changing the time

. With the oven

switched off, press

until it shows

/

(2.2.1), or press

and hold it down for

a few seconds (2.2.2). The time will fl ash.
Adjust it by turning the

dial (2.2.3, 2.2.4).

The hour will automatically be validated after
a few seconds.

2.3 Beeper function . Press

or

until

appears (2.3.1, 2.3.2). Adjust the

time turning the

dial (2.3.3). The time

will automatically be validated after a few
seconds and the countdown will start. A
beep will sound when the countdown ends.
Press any button to stop the beep.

2.4 Before using your new oven for the fi rst

time, heat it up while empty (with no food
in it and with the control turned to

, for

30 minutes at 250ºC). It may produce some
smoke or a bad smell (this is normal and is
caused by the oven heating up grease residue
etc.). When it has cooled down, pre-clean it
by wiping the inside with a damp cloth.

2.5 Accessories. Depending on the model

there is a Deep Tray (2.5.1), Flat Tray (2.5.2)
and Multifunctional Grill (2.5.3) that work
separately. If it also possible to combine
either tray with the Multifunctional Grill
(2.5.4) to make a set. All the accessories
or sets can be used directly or mounted
on the Partial Extraction Grill (2.5.5) or the
Total Extraction Grill (2.5.6, 2.5.7), (2.5.8).
If you have the partial extraction tray, it can
be used separately or together with trays
(3 types) (2.5.9). The Simple Grill is used
separately (2.5.10). If you have telescopic
rails, remove the tray before installing them in
the oven (2.5.11). The telescopic rails extend
automatically due to the weight of the tray
when the oven is opened (2.5.12). Food must
always be placed on a tray on the telescopic
rails (2.5.13). Bear in mind the position of the
grills when installing them. There are anti-
tipping stops at the sides (2.5.14).

2.6 Accessory positions. The accessories

can be fi tted in 5 different positions

.

2.7 Cooking the food. Place the food in the

oven. Choose the accessory or accessories
to be used and their recommended position,
or consult the cooking table. Close the oven
door.

COOKING

2.8 Selecting the cooking function

. Turn

the function selector

and select the

desired function according to the model.

Traditional fanned heat. For any kind of

dish. Several dishes may be cooked at once
without their fl avours or smells mixing.

Turbo plus. The heat is produced by the

central element. On the “ f ” model, it uses
this function for defrosting, setting the
temperature to 35ºC.

Master Chef. Smart cooking system.

Advertising
This manual is related to the following products: