Pioneer VSX-859RDS-G - Manual (Page 26)

26
En
Displays & Controls
VIDEO SELECT button
Switches the receiver between the various
types of video input.
MULTI CH INPUT button (See p. 34, 55)
Use to hook up an external component that can
decode other types of signals and input them
into the VSX-839RDS.
INPUT ATT button
Use to lower the input level of an analog signal
that is too powerful, thus causing the sound to
distort (the OVERLOAD indicator will light
when this is the case).
DIGITAL NR button
Press to switch Digital NR on or off (see page
52).
FL DIMMER button (See p. 56)
Use to adjust the brightness of the fluorescent
display (FL = fluorescent display).
Four levels of the brightness ranging from very
dim to very bright can be selected. Each press
changes the brightness of the display.
REMOTE SETUP button
Use to customize the remote control functions
and the remote control itself (see “Setting Up
the Remote Control to Control Other Compo-
nents“ starting on p. 68).
SYSTEM SETUP button
Use to set up the speaker and sound systems.
For more information see “Setting up for
Surround Sound“
starting on p. 30.
SIGNAL SELECT button
Press SIGNAL SELECT repeatedly to select one
of the following:
ANALOG – Analog signal.
DIGITAL – Digital signal (DVD/LD, TV/SAT, CD,
CD-R/TAPE 1/MD, VCR 1/DVR, VCR 2).
AUTO – This is the default. If there are analog
and digital input signals, the receiver automati-
cally selects the best possible signal.
EFFECT / CH SEL button
For DSP/advanced theater sound modes use to
put into the mode to add or subtract the amount of
effect. For other sound modes use to select
individual channels to increase or decrease
channel level.
EFFECT +/– buttons
Use to add or subtract the amount of effect in
different DSP/advanced listening sound modes or
the level of individual channels.
4 The following set of four buttons are
dedicated to TV control They are only
for controlling your TV.
Remote Control (VSX-839RDS)
1 SOURCE button
Use to turn on/off other components connected to
the receiver.
2 MULTI CONTROL buttons
Use to put the receiver/remote control in the
stated mode.
For other equipment controls, see "Using the
Remote Control with Other Components" on
pages 77 – 83.
3 NUMBER/MODE buttons
Use the number buttons to select the radio
frequency in tuner DIRECT ACCESS mode or the
tracks in CD, DVD mode etc.
Also, buttons marked with the following names
have special functions. If you try to use one of
these functions but the display flashes it means that
function cannot be used in the current mode (for
example DSP modes cannot be used when 5.1 CH
setting is on).
LOUDNESS button
Use to switch on the loudness. This feature is
useful for getting good bass and treble sounds
listening at low volumes.
Î
SOURCE
LOUDNESS
INPUT ATT DIGITAL NR FL DIMMER
REMOTE SETUP SYSTEM SETUP SIGNAL SELECT
TV VOL TV
TVFUNK
ENTER
TUNE
TUNE
D.ACCESS BAND
MENU
CLASS
RETURN
MIDNIGHT DSP STEREO FUNCTION
ADVANCED STANDARD MUTE
CLEAR AUDIO
AV PRE-PROGRAMMED AND LEARNING
REMOTE CONTROL UNIT
RECEIVER DIRECT CONTROL
MPX
ST ST
CHANNEL
EFFECT/CH SEL
RECEIVER
TV CONTROL
MASTER VOLUME
VIDEO SELECT
MULTI CONTROL
MULTI CH INPUT
DVD
CD CD-R TUN TVC
RECEIVER
1 2 3
4 5 6
7 8 9
! ⁄
0
* ‹ &
TV VCR
1 VCR
2
4 ¢
¶
DISC +10
TOP MENU
SETUP
/ DTS / MPEG
DISPLAY RF ATT
2
THX
1
=
~
!
@
8
9
0
3
4
6
2
-
7
+
£
%
¢
∞
^
(
)
¡
_
&
*
™
#
$
5