Det-Tronics X2200 UV Flame Detector with Pulse Output - Manual (Page 22)

95-8552 5.3 20
REPlaCEmENT PaRTS
The detector is not designed to be repaired in the field.
If a problem should develop, refer to the Troubleshooting
section. If it is determined that the problem is caused by
an electronic defect, the device must be returned to the
factory for repair.
DEVICE REPaIR aND RETURN
Prior to returning devices, contact the nearest local
Detector Electronics office so that a Return Material
Identification (RMI) number can be assigned. A
written statement describing the malfunction must
accompany the returned device or component to
assist and expedite finding the root cause of the
failure
.
Pack the unit properly. Always use sufficient packing
material. Where applicable, use an antistatic bag as
protection from electrostatic discharge.
NOTE
Inadequate packaging that ultimately causes
damage to the returned device during shipment
will result in a service charge to repair the
damage incurred during shipment.
Return all equipment transportation prepaid to the factory
in Minneapolis.
NOTE
It is highly recommended that a complete spare
be kept on hand for field replacement to ensure
continuous protection.
ORDERINg INfORmaTION
When ordering, please specify:
X2200 UV Flame Detector with Pulse Output
Refer to the X2200 Model Matrix for details.
Q9033 mount is required:
Q9033A for aluminum detectors only.
Q9033B for aluminum and stainless steel detectors.
X-SERIES FLAME DETECTOR ACCESSORIES
part Number Description
000511-029 Converter RS485 to RS232
001680-001 Window cleaner (6 pack)
005003-001 1 oz grease for detectors (non-silicon)
006097-001 Q1201 Laser
007240-001 Q1116A1001, Air Shield (AL)
007255-001 Q1201C1001 X-Series Laser Holder (AL/Plastic)
007290-001
Q9033B Stainless Steel Swivel Mount Assembly is for
aluminum and stainless steel detectors
007290-002
Q9033A Aluminum Swivel Mount Assembly is for aluminum
detectors only
007307-001 oi plate for X3301 (requires inspector connector to calibrate)
007307-002
oi plate for X52/X22/X98 (requires inspector connector to
calibrate)
007307-003 oi plate for X3302 (requires inspector connector to calibrate)
007338-001 Q2000A1001 X-Series Weather Shield (AL)
007338-010 Q2033A10R X3301/X3302 FOV Limiter 10° (AL)
007338-020 Q2033A20R X3301/X3302 FOV Limiter 20° (AL)
007338-030 Q2033A30R X3301/X3302 FOV Limiter 30° (AL)
007739-001 Magnet and Extension Pole
007818-001 Q1118A1001 Aluminum Air Shield/Flange Mount (AL)
007818-002 Q1118S1001 Stainless Steel Air Shield/Flange Mount (SS)
007819-001
W6300B1002 Inspector Connector (Inspector Monitor
software included)
007912-010 Spare Restrictor Plate 10° (AL)
007912-020 Spare Restrictor Plate 20° (AL)
007912-030 Spare Restrictor Plate 30° (AL)
009177-001 Q1120A1001 Paint shield mounting ring (AL)
009199-001 Q1198A1001 Dual Air Shield/Flange Mount (X9800 only)/(AL)
009207-001 Inspector Monitor CD
009208-001 oi kit (5 plates) with Inspector Connector and Monitor X3301
009208-002
oi kit (5 plates) with Inspector Connector and Monitor X52/
X22/X98
101197-003 Stop Plug, SS, IP66, Ex d e, M25 (SS)
102740-002 Magnet
102871-001 Laser Battery, 3V Lithium (laser)
103922-001 Model 475 HART Communicator
103363-001 14mm Hex Wrench (Steel)
103406-001 Screwdriver
103517-001 Stop Plug, AL, IP66, Ex d e, M25 (AL)
107427-040 O-ring - Rear Cover (Viton)