Rockwell Automation 1395 Reel Tension Paster Adapter User Manual
User manual
Advertising
Table of contents
Document Outline
- Front Cover
- Important User Information
- Table of Contents
- Preface
- Chapter 1
- Chapter 2
- Chapter 3
- Introduction
- Terminology
- Preliminary Steps
- 1. If a Drive that has already been installed is receiving a Digital Adapter Board as an added fe...
- 2. If a given Drive for any reason loses the EE memory information, it will also be necessary to ...
- 3. Should there be a need to check or download Parameters to the Drive, use of the ITS device wil...
- ITS (Monitor)
- ITS (Download)
- DHT (HandHeld Programming Terminal)
- StartUp Checklist
- Table 1: Link List
- 450
- 151
- 152
- 153
- 154
- 161
- 163
- 164
- 165
- 166
- 250
- TO
- TO
- TO
- TO
- TO
- TO
- TO
- TO
- TO
- TO
- TO
- 100
- 400
- 200
- 404
- 403
- 407
- 405
- 408
- 410
- 411
- 100
- *
- *
- *
- *
- *
- *
- *
- *
- *
- *
- *
- *
- *
- 551
- 553
- 558
- 559
- 561
- 562
- 563
- 564
- 565
- 566
- 567
- 569
- 570
- 571
- 600
- 601
- 602
- 603
- 606
- 607
- 608
- 609
- 610
- 611
- 612
- 613
- 614
- 615
- 616
- 617
- 621
- 628
- 633
- 634
- 635
- 651
- 652
- 659
- 660
- 661
- 663
- 664
- 713
- 714
- 715
- 716
- 717
- 718
- 719
- 720
- 721
- 722
- 724
- 725
- 726
- 727
- 728
- 730
- 731
- 732
- 733
- 734
- 735
- 736
- 737
- 738
- 739
- 740
- 0.0
- 0.0
- 1500
- 750
- 131
- 2566
- 400
- 1700
- 150
- 425
- 50
- 30
- -20
- 0
- 625
- 721
- 659
- 660
- 1750
- -20
- 1560
- 210
- 500
- 20.6
- 1.2
- 6
- 5.78
- 40
- 2.1
- 460
- 0
- 1
- 20
- -20
- 0
- 20
- 10
- 400
- 150
- 65535
- 150
- 150
- 0
- 0
- 0
- 4096
- -165
- 165
- -1
- 150
- 0
- 1750
- 75
- 10
- 10
- 2
- 1
- 1
- 15
- 0.5
- 1
- 155
- 1659
- 136
- 16384
- 512
- 12350
- 7200
- Control Boards
- Cross Reference
- Speed Match
- Dancer Calibration
- Drive Not Started
- Preliminary Steps:
- A. Disable the process trim system by setting Parameter 628 to zero.
- B. Disable the integral channel of the P/I Regulator by setting Parameter 567 to zero.
- 1. Using a digital voltmeter, monitor test point TP14 to TP12 on the Digital Reference Adapter Bo...
- 2. Once step 1 is complete, the dancer should be allowed to move freely. Move the dancer up and d...
- Drive Started
- 1. Determine the proper gear pulse per revolution from the printing diameter cross reference char...
- 2. Determine the maximum belt motor RPM versus maximum press speed (IMP/HOUR) from this same char...
- 3. Determine the maximum drive shaft speed of the press (usually 2566 RPM), versus maximum press ...
- 4. Monitor the Drive speed on the DHT or use the ITS via a computer and monitor Parameter 106 – V...
- 5. With the GSD console in Emulate, start the Drive with the Emulate reference at a comfortable m...
- 6. Run the reel to maximum press speed and adjust the Drive reference for proper maximum speed. T...
- Running With Paper – Important Preliminary Steps:
- Final Speed Match:
- 1. The preset #1 speed of +20 RPM is the default, assuming that the press speed during auto slack...
- 2. The Max Press Ref RPM, Parameter 562 will again be used to make the final speed matching adjus...
- 3. The RTP Drive should be tracked at maximum speed with a roll of paper at least 75% of full roll.
- 4. If the press is to remain at a given maximum speed for a period of time, and a significant amo...
- 5. The integral gain of the P/I Regulator will remove all of the dancer movement downward as the ...
- 6. To adjust the dancer position during normal run, Parameter 553 should be changed accordingly. ...
- Chapter 4
- Index
- Back Cover