Document Outline

• Preface
  • Conventions used in this document
  • Safety terms and symbols
• Chapter 1 KTD-405/405A/405-2D overview
  • Product overview
    • Product contents
      • Figure 1. KTD-405 package contents
      • Figure 2. KTD-405A package contents
  • Operating modes
    • Digiplex mode
      • Figure 3. LCD menus showing standard and hybrid modes
    • Zone mode
      • Figure 4. LCD display of zone mode
• Chapter 2 Installation
  • Installation guidelines
    • Table 1. Recommended cable types
  • Back panel connections
    • KTD-405/KTD-405-2D connections
      • Figure 5. KTD-405/KTD-405-2D back panel connections
    • KTD-405A connections
      • Figure 6. KTD-405A back panel connections
  • I/O box connections
    • RJ-cable connections
      • Figure 7. RJ-cable connections to the I/O box
    • Twisted-pair connections
      • Figure 8. Wire connections to the I/O box
    • Connecting a multiplexer or DVMRe and domes
      • Figure 9. Connecting a keypad (KTD-405 shown) to a multiplexer or DVMRe (shown) and domes
    • Connecting multiple keypads with RJ45 cables
      • Figure 10. KTD-405, KTD-405-2D, and KTD-405A connections via RJ45 cables
    • Connecting multiple keypads with STP cable
      • Figure 11. KTD-405 and KTD-405A connections via STP cables
    • Connecting new and old I/O boxes
      • Figure 12. New to old I/O box connection
    • Setting audio attenuation
      • Figure 13. Audio I/O board with attenuation jumpers
• Chapter 3 Programming
  • Programming modes
    • Figure 14. Menu keys (gray keys are available on the KTD-405A only)
    • Table 2. Navigating the programming menus
    • Entering programming modes
      • Figure 15. Normal operating display
      • Figure 16. ENTER PROGRAMMING CODE menu
  • Supervisor programming
    • Figure 17. Supervisor programming menu tree
    • Figure 18. KB3 PTZ PROTOCOL display
    • Figure 19. ENTER REMOTE PRGMG display
    • Figure 20. KEYPAD TITLE display
    • Figure 21. KEYPAD LOCKOUT PRIORITY displays
    • Figure 22. Lowest user programmed preset menu
    • Figure 23. PROGRAM SOFT KEYS display
    • Figure 24. PRESS KEY TO PROGRAM display
    • Figure 25. Command selection display
    • Figure 26. Confirm command selection display
    • Figure 27. CHANGE ACCESS CODES displays
    • Figure 28. BAUD RATE display
    • Figure 29. SYSTEM CONTROL display
    • Figure 30. INACTIVE TIMEOUT display
  • User programming
    • Figure 31. OPERATING MODE menu
    • Standard Digiplex menus
      • Figure 32. Maximum settings
      • Figure 33. Access menus
      • Figure 34. VCR access display
      • Figure 35. Multiplexer access display
      • Figure 36. MONITOR OFFSET display
      • Figure 37. ANNUNCIATION displays
    • Zone menus
      • Figure 38. OPERATING MODE menu
      • Figure 39. Zone menu
      • Figure 40. ENTER ZONE ADDRESS menu
      • Figure 41. ZONE xx TITLE menu
      • Figure 42. SEND TO ALL KEYPADS display
      • Figure 43. Zone hub display
      • Figure 44. Zone monitor outputs
      • Figure 45. Zone camera inputs
      • Figure 46. Access restriction menus
      • Figure 47. ZONE xx ACCESS menu
      • Figure 48. Annunciation menu
      • Figure 49. Call tone menu
      • Figure 50. SPOT MONITOR NUMBER menu
  • Remote programming
    • Figure 51. Remote programming menu tree
    • Quick Shadow Tour 1 programming short cut
      • Figure 52. Normal operating display
      • Figure 53. PROGRAM SHADOW TOUR display
      • Figure 54. END SHADOW TOUR PROGRAMMING display
• Chapter 4 Operation
  • Operating your keypad
    • Table 3. Normal and shifted key functions
  • Standard Digiplex mode
    • Figure 55. Normal operating display
    • Selecting a monitor
    • Selecting a camera
    • Controlling a camera
    • Setting a preset
    • Recalling a preset
    • Operating group switching on Digiplex IV switchers
      • Figure 56. Enter monitor group menu
      • Figure 57. Enter group sequence menu
    • Setting autopan limits
    • Controlling a DVMRe/multiplexer (hybrid mode)
    • Controlling a recording device
      • Table 4. Controlling a recording device
    • System information menus
      • Figure 58. Maximum values
    • Help menu
      • Figure 59. HELP menu
    • Audio
      • Figure 60. Normal operating display with annunciation
  • Zone mode
    • Figure 61. Zone mode main menu
    • Table 5. Controlling a multiplexer
    • Table 6. Navigating Calibur menu
    • Programming a DVMRe/multiplexer camera sequence
      • Figure 62. Enter sequence menu
• Chapter 5 Troubleshooting and support
  • Troubleshooting your keypad
  • Contacting us
    • Table 7. Technical support
    • Online resources
• Appendix A Sample configurations and charts
  • Sample analog system configurations
    • Figure 63. Typical KTD-405/KTD-405-2D Digiplex configuration
    • Figure 64. Typical KTD-450A Digiplex configuration
    • Figure 65. Zone configuration
    • Old I/O box connections
      • Figure 66. Old I/O box connections for audio and nonaudio keypads
      • Figure 67. Connecting a multiplexer or DVMRe to the old I/O box
    • Connecting multiple keypads to the old I/O box
      • Figure 68. Multiple KTD-405 connections
      • Figure 69. KTD-405/KTD-405-2D to KTD-405A connections
  • Sample IP system configuration
    • Figure 70. SymDec 16 plus 4 single-zone system configuration
  • Receiver site addressing
    • Figure 71. Receiver site address DIP switches (set to 209)
    • Table 8. Dip switch positions and equivalent values
    • Table 9. Receiver site addressing values by zone
  • Reprogrammable keys and commands
    • Figure 72. Normal operating display
    • Figure 73. Code entry display
    • Figure 74. PROGRAM SOFT KEYS display
    • Figure 75. Keys that can be reprogrammed
    • Table 10. Commands that can be assigned to reprogrammed keys
  • System planning chart
• Index