Audio Enhancement TLD100 - Manual (Page 32)

32
Command Content Type 1st parameter 2nd parameter Command example
SDS Tone setting Setting 2: Tone 0: Disable
1: Enable
$SDS:2:1[CR][LF]
Response Same as above Same as above $SDS:2:1[CR][LF]
Tone Level setting Setting 3: Tone Level 0: Low, 1: High $SDS:3:0[CR][LF]
Response Same as above Same as above $SDS:3:0[CR][LF]
Microphone/Line
Mixing setting
Setting 4: Microphone/Line
Mixing
0: Disable
1: Enable
$SDS:4:1[CR][LF]
Response Same as above Same as above $SDS:4:1[CR][LF]
Feedback Blocker
setting
Setting 5: Feedback Blocker 0: Disable
1: Enable
$SDS:5:0[CR][LF]
Response Same as above Same as above $SDS:5:0[CR][LF]
Remote Volume
setting
Setting 6: Remote Volume 0: Disable
1: Enable
$SDS:6:1[CR][LF]
Response Same as above Same as above $SDS:6:1[CR][LF]
QDS* State query of
Microphone
Override setting
Query 1: Microphone Override None $QDS:1[CR][LF]
Response Same as above 0: Disable
1: Enable
$QDS:1:0[CR][LF]
State query of
Tone setting
Query 2: Tone None $QDS:2[CR][LF]
Response Same as above 0: Disable
1: Enable
$QDS:2:1[CR][LF]
State query of
Tone Level setting
Query 3: Tone Level None $QDS:3[CR][LF]
Response Same as above 0: Low, 1: High $QDS:3:0[CR][LF]
State query of
Microphone/Line
Mixing setting
Query 4: Microphone/Line
Mixing
None $QDS:4[CR][LF]
Response Same as above 0: Disable
1: Enable
$QDS:4:1[CR][LF]
State query of
Feedback Blocker
setting
Query 5: Feedback Blocker None $QDS:5[CR][LF]
Response Same as above 0: Disable
1: Enable
$QDS:5:0[CR][LF]
State query of
Remote Volume
setting
Query 6: Remote Volume None $QDS:6[CR][LF]
Response Same as above 0: Disable
1: Enable
$QDS:6:1[CR][LF]
CVU Notification of vol-
ume up operation
from microphone
Change
notification
1: MIC1 input volume up
2: MIC2 input volume up
L:LINE input volume up
None $CVU:1[CR][LF]
CVD Notification of
volume down
operation from
microphone
Change
notification
1: MIC1 input volume
down
2: MIC2 input volume
down
L: LINE input volume
down
None $CVD:L[CR][LF]
SRS Reset volume and
F1/F2 states
Setting None None $SRS[CR][LF]
Response None None $SRS[CR][LF]
* Each QDS response command returns not the physical ON/OFF status of the DIP switch but the current setting status
of the corresponding function.
Volume list
Parameter Volume Parameter Volume Parameter Volume
00 0 dB 08 –16 dB 16 –32 dB
01 –2 dB 09 –18 dB 17 –36 dB
02 –4 dB 10 –20 dB 18 –40 dB
03 –6 dB 11 –22 dB 19 –44 dB
04 –8 dB 12 –24 dB 20 –48 dB
05 –10 dB 13 –26 dB 21 –60 dB
06 –12 dB 14 –28 dB 22 –72 dB
07 –14 dB 15 –30 dB
•