Flowserve CPXV fitted with Mark 3 ASME hydraulics - Manual (Page 42)

CPXV with Mark 3 ASME hydraulics ENGLISH 71569291 12-14
Page 42 of 44
flowserve.com
8.3 Parts interchangeability
Refer to the factory to ensure interchangeability
between different sizes of casing which follow.
Casing size Impeller drive group
1K1.5x1-6 1K
1K3x1.5-6 1K
1K3x2-6 1K
1K1.5x1-8 1K
1K3x1.5-8 1K
2K3x2-8 2K
2K2x1-10A 2K
2K3x1.5-10A 2K
2K3x2-10A 2K
2K4x3-10 2K
2K4x3-10H 2K
2K6x4-10 2K
2K6x4-10H 2K
2K3x1.5-13 2K
2K3x1.5LF-13 2K
2K3x2-13 2K
2K4x3-13 2K
2K4x3-13HH 2K
2K6x4-13A 2K
3K8x6-14A 3K
3K10x8-14 3K
3K6x4-16 3K
3K8x6-16A 3K
3K10x8-16 3K
3K10x8-16H 3K
3K10x8-17 3K
8.4 General arrangement drawing
The typical general arrangement drawing and any
specific drawings required by the contract will be sent
to the Purchaser separately unless the contract
specifically calls for these to be included into the User
Instructions. If required, copies of other drawings
sent separately to the Purchaser should be obtained
from the Purchaser and retained with these User
Instructions.
9 CERTIFICATION
Certificates determined from the Contract
requirements are provided with these Instructions
where applicable. Examples are certificates for CE
marking, ATEX marking etc. If required, copies of
other certificates sent separately to the Purchaser
should be obtained from the Purchaser for retention
with these User Instructions.
10 OTHER RELEVANT
DOCUMENTATION AND MANUALS
10.1 Supplementary User Instruction
manuals
S upplementary instruction determined from the contract
requirements for inclusion into User Instructions such as
for a driver, instrumentation,
controller, sub-driver, seals,
sealant system, mounting component etc are included
under this section. If further copies of these are
required they should be obtained from the purchaser for
retention with these User Instructions.
Where any pre-printed set of User Instructions are
used, and satisfactory quality can be maintained only
by avoiding copying these, they are included at the
end of these User Instructions such as within a
standard clear polymer software protection envelope.
10.2 Change notes
If any changes, agreed with Flowserve, are made to
the product after its supply, a record of the details
should be maintained with these User Instructions.
10.3 Additional sources of information
Reference 1:
NPSH for Rotordynamic Pumps: a reference guide,
Europump Guide No. 1, Europump & World Pumps,
Elsevier Science, United Kingdom, 1999.
Reference 2:
Pumping Manual, 9
th
edition, T.C. Dickenson,
Elsevier Advanced Technology, United Kingdom, 1995.
Reference 3:
Pump Handbook, 2
nd edition, Igor J. Karassik et al,
McGraw-Hill Inc., New York, 1993.
Reference 4:
ANSI/HI 1.1-1.5. Centrifugal Pumps - Nomenclature,
Definitions, Application and Operation.
Reference 5:
ANSI B31.3 - Process Piping.
Reference 6:
ESA
– Guidelines for Safe Seal Usage (Flanges and
Gaskets).