Verilink DIU 2130 (880-503297-001) Product Manual - Manual (Page 30)

DIU 2130 Configuration
3-6 Verilink
At the prompt enter port 2 channels > enter port 2 channels > enter port 2 channels > enter port 2 channels > type 13-24 and press ENTER.
This assigns timeslots 13 through 24 to Data Port 2.
Press ENTER again to refresh the display with the timeslot (DS0)
assignments.
Figure 3-3 DIU 2130 Configuration Menu
Lead toggles are used to determine whether the control leads on
the synchronous serial interface will function in the normal way or
be forced on. When the DTE does not assert control leads they can
be forced on by typing the three letter abbreviation of the control
lead. For this example, the DTE supports normal control lead
operation and the default values are appropriate.
Mode is used to determine the data rate of each of the timeslots
assigned to the port. For an AMI T1 circuit the mode must be 56K.
For the B8ZS T1 used in this example, 64K provides greater
throughput. Use the M1 and M2 commands (replacing the “p” with
the appropriate port number) to set both data ports to 64K per DS0.
The remaining options are correct for this example. The T1 circuit
and DTE should now be connected.
Once the CSU has been connected to the T1 circuit for at least
fifteen minutes, meaningful performance statistics will be available
under the controller module’s Performance Monitoring Menu. See
the appropriate controller module user manual for more
information.
--- DIU 2130 CONFIGURATION/DIAGNOSTIC MENU --- --- DIU 2130 CONFIGURATION/DIAGNOSTIC MENU --- --- DIU 2130 CONFIGURATION/DIAGNOSTIC MENU --- --- DIU 2130 CONFIGURATION/DIAGNOSTIC MENU ---
C) CSU [ 1,1 ] C) CSU [ 1,1 ] C) CSU [ 1,1 ] C) CSU [ 1,1 ]
T) timing source CSU
T) timing source CSU T) timing source CSU T) timing source CSU
chnl 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 chnl 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 chnl 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 chnl 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
Dp)port 01 01 01 01 01 01 01 01 01 01 01 01 02 02 02 02 02 02 02 02 02 02 02 02
Dp)port 01 01 01 01 01 01 01 01 01 01 01 01 02 02 02 02 02 02 02 02 02 02 02 02 Dp)port 01 01 01 01 01 01 01 01 01 01 01 01 02 02 02 02 02 02 02 02 02 02 02 02 Dp)port 01 01 01 01 01 01 01 01 01 01 01 01 02 02 02 02 02 02 02 02 02 02 02 02
Lead Toggles DTR) DSR) RTS) CTS) DCD) Lead Toggles DTR) DSR) RTS) CTS) DCD) Lead Toggles DTR) DSR) RTS) CTS) DCD) Lead Toggles DTR) DSR) RTS) CTS) DCD)
Forced Ports -/- -/- -/- -/- -/-
Forced Ports -/- -/- -/- -/- -/- Forced Ports -/- -/- -/- -/- -/- Forced Ports -/- -/- -/- -/- -/-
Port 1 Port 2 Statistics Port 1 Port 2 Statistics Port 1 Port 2 Statistics Port 1 Port 2 Statistics
Mp) mode 56K 56K FW/HW Rev.............1.6/0.8
Mp) mode 56K 56K FW/HW Rev.............1.6/0.8 Mp) mode 56K 56K FW/HW Rev.............1.6/0.8 Mp) mode 56K 56K FW/HW Rev.............1.6/0.8
Sp) scram/hdlc inv N/N N/N Battery...............OK
Sp) scram/hdlc inv N/N N/N Battery...............OK Sp) scram/hdlc inv N/N N/N Battery...............OK Sp) scram/hdlc inv N/N N/N Battery...............OK
Kp) clocking ST ST DTE Intf..............V.35/V.35
Kp) clocking ST ST DTE Intf..............V.35/V.35 Kp) clocking ST ST DTE Intf..............V.35/V.35 Kp) clocking ST ST DTE Intf..............V.35/V.35
Gp) LOS lead NONE NONE Data bus..............A
Gp) LOS lead NONE NONE Data bus..............A Gp) LOS lead NONE NONE Data bus..............A Gp) LOS lead NONE NONE Data bus..............A
Ep) enable loop YES YES Tp) test and monitor BEC Ep) enable loop YES YES Tp) test and monitor BEC Ep) enable loop YES YES Tp) test and monitor BEC Ep) enable loop YES YES Tp) test and monitor BEC
Np) near loopback OFF OFF Pp) monitor leads and status
Np) near loopback OFF OFF Pp) monitor leads and status Np) near loopback OFF OFF Pp) monitor leads and status Np) near loopback OFF OFF Pp) monitor leads and status
Fp) far loopback ON OFF A) Alarm Enable......YES
Fp) far loopback ON OFF A) Alarm Enable......YES Fp) far loopback ON OFF A) Alarm Enable......YES Fp) far loopback ON OFF A) Alarm Enable......YES
[1,2] DIU 2130 > [1,2] DIU 2130 > [1,2] DIU 2130 > [1,2] DIU 2130 >