Yaskawa AC Drive Z1000 Bypass Technical Manual User Manual
Page 455
Metasys N2 Point Database ................................................... 430
Minimum Current Detection Level during Speed Search ................. 126
Minimum Wait Time for Sending Messages.......................... 383, 429
Minor Alarms ................................................................... 222
Minor Fault ...................................................................... 249
Minor Fault and Alarm Displays ............................................. 223
Minor Faults ..................................................................... 222
Minor Faults and Alarms ................................................ 221, 222
Model Number and Nameplate Check .........................................28
Modes ..............................................................................99
Modified Constants............................................................. 100
Momentary Overcurrent Protection .......................................... 300
Momentary Power Loss Minimum Baseblock Time................. 170, 324
Momentary Power Loss Operation Selection ......................... 125, 324
Momentary Power Loss Ride-Thru .................................... 169, 300
Momentary Power Loss Ride-Thru Time ............................. 170, 324
Monitor Parameters....................................................... 165, 334
Most Recent Fault .............................................................. 338
Motor 1 Parameters............................................................. 149
Motor Base Frequency ............................................. 113, 115, 332
Motor Base Speed ........................................................ 115, 332
Motor Data Error................................................................ 249
Motor d-Axis Current at Previous Fault ..................................... 338
Motor Does Not Rotate ........................................................ 254
Motor Hunting and Oscillation Control Parameters ....................... 220
Motor Iron Loss ........................................................... 115, 333
Motor is Too Hot ............................................................... 255
Motor No-Load Current........................................................ 149
Motor Overheat ................................................................. 243
Motor Overheat Alarm (PTC Input).......................................... 233
Motor Overheat Fault (PTC Input) ........................................... 233
Motor Overload ................................................................. 233
Motor Overload Estimate (oL1) .............................................. 341
Motor Overload Protection Selection .................................. 168, 324
Motor Overload Protection Time ....................................... 169, 324
Motor Performance Fine-Tuning ............................................. 220
Motor Poles...................................................................... 113
Motor Protection .......................................................... 168, 300
Motor Pull Out or Step Out Detection ....................................... 236
Motor q-Axis Current at Previous Fault ..................................... 338
Motor Rated Current ......................................... 113, 115, 149, 332
Motor Rated Power ....................................................... 114, 332
Motor Rated Voltage ............................................... 113, 114, 332
Motor Rotates Faster Than the Frequency Reference...................... 256
Motor Rotates in One Direction Only........................................ 255
Motor Stalls During Acceleration or With Large Loads .................. 256
Motor Underload................................................................ 237
Motor Underload Protection Level at Minimum Frequency ........ 179, 326
Motor Underload Protection Selection................................. 178, 326
Motor Wiring......................................................................63
Multi-Function Analog Inputs ................................................ 160
Multi-Function Analog Input Selection Error............................... 247
Multi-Function Analog Input Terminal Settings ........................... 161
Multi-Function Analog Outputs .............................................. 165
Multi-Function Analog Output Terminal AM Bias ........................ 166
Multi-Function Analog Output Terminal AM Gain........................ 166
Multi-Function Analog Output Terminal AM Monitor Selection........ 165
Multi-Function Analog Output Terminal AM Signal Level Selection .. 167
Multi-Function Analog Output Terminal FM Bias......................... 166
Multi-Function Analog Output Terminal FM Gain ........................ 166
Multi-Function Analog Output Terminal FM Monitor Selection ........ 165
Multi-Function Analog Output Terminal FM Signal Level Selection... 167
Multi-Function Digital Input Terminal Settings............................ 151
Multi-Function Digital Outputs............................................... 153
Multi-Function Input Selection Error ........................................ 246
Multiple Connection Diagram .............................. 359, 379, 406, 422
Multi-Step Speed Selection.................................................... 142
N
n1-02.............................................................................. 220
N2 Configuration ............................................................... 420
N2 Serial Communication ..................................................... 423
N2 Setup Parameters ........................................................... 423
N2 Specifications ............................................................... 420
Network Digital Input Select.................................................. 213
Network Termination .............................................. 358, 379, 422
No-Load Current Alarm ....................................................... 249
No-Load Current Error......................................................... 250
Notes on Stationary Auto-Tuning ............................................ 112
nSE ............................................................................... 231
Number of Auto Restart Attempts...................................... 174, 325
Number of Motor Poles .................................................. 115, 332
Number of Run Commands ................................................... 340
Number of Speed Search Restarts ............................................ 127
O
oC ................................................................................. 231
oFA00 ............................................................................ 232
OFF button Input ............................................................... 250
OFF Key ...........................................................................92
oH ........................................................................... 232, 243
oH1 ............................................................................... 232
oH2 ............................................................................... 243
oH3 ......................................................................... 233, 243
oH4 ............................................................................... 233
oH Pre-Alarm Time Limit ..................................................... 160
oL1................................................................................ 233
oL2................................................................................ 234
oL3.......................................................................... 234, 243
oL7................................................................................ 234
oPE ............................................................................... 246
oPE01 ............................................................................ 246
oPE02 ............................................................................ 246
oPE03 ............................................................................ 246
oPE05 ............................................................................ 247
oPE07 ............................................................................ 247
oPE09 ............................................................................ 247
oPE10 ............................................................................ 247
oPE11 ............................................................................ 247
oPE28 ............................................................................ 248
oPE Fault Parameter............................................................ 337
Operation Errors .......................................................... 221, 223
Operation Status Monitors..................................................... 194
Operator Related Settings...................................................... 183
oPr ................................................................................ 235
Option Card Connection Error at Option Port CN5........................ 232
Option card connector (CN5) ...................................................36
Option Card External Fault.............................................. 226, 241
Option Communication Error ........................................... 224, 240
Option Frequency Reference .................................................. 341
Index
YASKAWA ELECTRIC SIEP YAIZ1B 01D YASKAWA AC Drive – Z1000 Bypass Technical Manual
455