Extron electronic Multi-Graphic Processor MGP 464 DI - Manual (Page 33)

3-9 MGP 464 • Operation
PRELIMINAR
Y
Input Configuration menu
The Input Configuration menu allows you to select a video signal type for each
of the four fully configurable inputs. All of these inputs can accept the following
video signals: RGB, YUV-HD, YUVi, RGBcvS, S-video, composite video, DVI
(MGP 464 DI and MGP 464 HD-SDI only), and HD-SDI (MGP 464 HD-SDI only);
RGB is the default. You can also select the horizontal and vertical start positions,
pixel sampling phase for the four windows (except for YUVi, S-video, and
composite video inputs), total pixels, active pixels, and active lines for each input.
Rotate the horizontal Adjust ([) knob to cycle through the four inputs, and the
vertical Adjust knob ({) to adjust the setting.
N The 15 virtual inputs (numbered 5 through 19) cannot be configured from the
front panel; you must use SIS commands, the Windows-based control software,
or the MGP 464 Web pages.
Next
Next
Input #1
Film Mode ON
Next
Film Mode
Turn Film Mode on
or off (for low-
resolution devices). Input
• Input #1
• Input #2
• Input #3
• Input #4
Input #1
RGB
Input video type
Select a signal format:
• RGB
• YUV-HD
• RGBcvS
• YUVi
• S-video
• Composite
• DVI (MGP 464 DI and
MGP 464 HD-SDI only)
• HD-SDI (MGP 464 HD-SDI only) Input
• Input #1
• Input #2
• Input #3
• Input #4
Next Input #1
Vert Start 0128
Next
Input
• Input #1
• Input #2
• Input #3
• Input #4 Vertical Start
Select a vertical
start line position
for the top edge of
the active video.
Input #1
Horz Start 0128
Input
• Input #1
• Input #2
• Input #3
• Input #4 Horizontal Start
Select a horizontal
start pixel position
for the left edge of
the active video. Input
• Input #1
• Input #2
• Input #3
• Input #4
Input #1
PxPhs Win#1 16
Input
• Input #1
• Input #2
• Input #3
• Input #4 Pixel Phase 1
Adjust the pixel
sampling point
for window 1 for
each input.
Input #1
Total Pxl 1688
Input
• Input #1
• Input #2
• Input #3
• Input #4 Total Pixels
Specify the width in
pixels of the total
image area to be
sampled.
Next Next
Input #1
Active Pxl 1280
Input
• Input #1
• Input #2
• Input #3
• Input #4 Active Pixels
Specify the width
in pixels of the
active image area
to be sampled.
Next
Input #1
Active Lns 1024
Input
• Input #1
• Input #2
• Input #3
• Input #4 Active Lines
Specify the height
in lines of the
active image area
to be sampled.
Next
Next
Input #1
PxPhs Win#2 16
Input
• Input #1
• Input #2
• Input #3
• Input #4 Pixel Phase 2
Adjust the pixel
sampling point
for window 2 for
each input.
Input
Configuration
Menu
Auto
Image
Input #1
PxPhs Win#3 16
Input
• Input #1
• Input #2
• Input #3
• Input #4 Pixel Phase 3
Adjust the pixel
sampling point for
window 3 for each
input.
Input #1
PxPhs Win#4 16
Input
• Input #1
• Input #2
• Input #3
• Input #4 Pixel Phase 4
Adjust the pixel
sampling point for
window 4 for each
input.
Next
Next
Input Configuration menu flow