Document Outline

• 1201 User's manual
• Table of contents
  • 1. General Information
    • 1.1 Feature Overview
    • 1.2 Warranty Information
    • 1.3 Precaution of Operation
    • 1.4 Upkeep of 1201
    • 1.5 Safety Information
    • 1.6 Symbols and Terms
    • 1.7 Inspection
    • 1.8 Options and Accessories
    • 1.9 1201's Dimension
  • 2. Overview
    • 2.1 Setting up your 1201 Digital Multimeter
      • 2.1.1 To adjust the handle
      • 2.1.2 Toconnect the power
        • 2.1.2.1 To convert the voltage
        • 2.1.2.2 To change the fuse
      • 2.1.3 Factory Default when Power-ON
    • 2.2 Features
    • 2.3 1201 Function Introduction
      • 2.3.1 The Front panel
      • 2.3.2 The Display
        • 2.3.2.1 Annunciators at upper side
        • 2.3.2.2 Annunciators at right side
      • 2.3.3 The Rear panel
  • 3. Basic Measurement Function
    • 3.1 Voltage Measurements (DC&AC)
    • 3.2 Current Measurements (DC&AC)
    • 3.3 Resistance Measurements (2&4-wire)
    • 3.4 Frequency&Period Measurements
    • 3.5 Continuity Measurements
    • 3.6 Diode Measurements
    • 3.7 Temperature Measurements
      • 3.7.1 Thermocouple Measurements
      • 3.7.2 RTD Measurements
        • 3.7.2.1 2-Wire RTD Measurements
        • 3.7.2.2 3-Wire RTD Measurements
        • 3.7.2.3 4-Wire RTD Measurements
  • 4. Front panel operations
    • 4.1 Measurement Configuration
      • 4.1.1 Set ADC (Auto Zero & Auto Gain)
      • 4.1.2 Filter
        • 4.1.2.1 AC Filter
        • 4.1.2.2 Digital Filter
      • 4.1.3 Resolution setting (Digits)
      • 4.1.4 DC Input Resistance
      • 4.1.5 Threshold Resistance (Continuity)
      • 4.1.6 Range (Manual and Auto)
      • 4.1.7 Rate (Integration Time)
      • 4.1.8 Sensor selection for Temperature
      • 4.1.9 Remote Interface selection
      • 4.1.10 Input Terminal Switch
    • 4.2 Trigger Operations
      • 4.2.1 Trigger Mode
      • 4.2.2 Trigger Source
      • 4.2.3 Trigger setting
    • 4.3 Math Operations
      • 4.3.1 Ratio
      • 4.3.2 % (Percent)
      • 4.3.3 Min/Max
      • 4.3.4 Null
      • 4.3.5 Limits Test
      • 4.3.6 MX+B
      • 4.3.7 dB/dBm
    • 4.4 Other system related operations
      • 4.4.1 Display
      • 4.4.2 Beeper
      • 4.4.3 Reading Memory (Store&Recall)
      • 4.4.4 Sensitivity Band (Hold)
      • 4.4.5 Scanning (Scan)
      • 4.4.6 Stepping (Step)
      • 4.4.7 Initial Mode
      • 4.4.8 Language
      • 4.4.9 Error cindition
      • 4.4.10 Firmware Revision
      • 4.4.11 Calibration
      • 4.4.12 Self-test
  • 5. Remote Interface operations
    • 5.1 Pass/Fail output from USB connector
    • 5.2 Setting up for remote interface
    • 5.3 Remote Interface commands
  • 6. Error Messages
    • 6.1 Error Type
      • 6.1.1 Execution Errors
  • Appendix
    • A. Specification List
    • B. General Specifications
    • C. Remote Interface reference
      • C.1 An Introduction to the SCPI Language
      • C.2 Output Data Formats
      • C.3 The MEASure? Command
      • C.4 The CONFigure Command
      • C.5 The Measurement Configuration command
      • C.6 The Math Operation command
      • C.7 The triggering commands
      • C.8 The System-Related commands
      • C.9 Status Reporting commands
      • C.10 SCPI Compliance Information
      • C.11 IEEE-488 Compliance Information
    • D. About Application Programs
      • LISTING D.1
      • LISTING D.2
      • LISTING D.3