FARGO electronic FARGO DTC 400 - Manual (Page 319)

RESTRICTED USE ONLY Fargo Electronics, Inc.
DTC400 Card Printer/Encoder User Guide (Rev. 2.6) 15-2
Delete button, 6-57
Device Option tab, 4-28
Diagnostic Utility / Diagnostics Tool, 6-5
dimension boxes, 6-76
Dimensions, 2-3
DIP switches (Dual In-line Package Switches), 15-4
Direct-to-Card (DTC) Printing, 15-5
Disable Printing option, 6-20
Disables Magnetic Verification, 4-53
disk cleanup utility, 4-4
Dither, 15-5
DMA (Direct Memory Access), 15-3
Dongle, 15-5
Dot, 15-5
Dot pitch, 15-5
Download, 15-5
DPI (Dot Per Inch), 15-5
DRAM (Dynamic Random Access Memory), 15-5
Driver, 15-5
DTC400/DTC300/DTC300M Card Printer, 8-1
Duplex Printing, 15-5
Dwell Time, 15-6
Dye Migration, 15-6
Dye-Sub Intensity setting, 4-44
Dye-Sublimation, 2-9, 15-6
Dye-Sublimation Cyan Panel, 2-11
Dye-Sublimation Magenta Panel, 2-11
Dye-Sublimation Yellow Panel, 2-11
Dye-Sublimation-Only Print Ribbons, 2-13
E
E-card, 15-6
E-card Docking Station, 15-6
ECP Mode (Enhanced Capabilities Port Mode), 15-6
Edge-to-Edge, 15-6
EE Memory, 15-6
EEPROM (Electrically Erasable Programmable Read
Only Memory), 15-6
embedded contaminants, 2-15, 4-41
Emissions Standards, 2-2
Enable MLE Support checkbox, 6-37
Encoder (smart card), 15-6
Encoder (wheel), 15-7
End Sentinel (ES)., 6-42
Engine, 15-7
EOF (End Of Form), 15-7
EPP (Enhanced Parallel Port), 15-7
EPROM (Electronically Programmable Read Only
Memory), 15-7
EPROM version number, 4-53, 4-54
Escape sequence, 15-7
ESD, 1-2, 6-1, 7-1, 9-1
ESD (ElectroStatic Discharge), 15-7
Ethernet, 15-7
excessive resin printing problems, 4-47
exposed to static electrical discharges, 7-2
F
Fargo Technical Support, 13-1
Fargo Technical Support via the Web, 13-1
FCC, 2-1
feed card into encoder, 4-4
Field Separator (FS), 6-42
Film, 15-7
Firmware, 15-7
Flash Memory, 15-8
Flipper Table Module, 2-16
Font, 15-8
For Overlay Only, 6-51
For Print and Overlay, 6-51
FPGA (Field Programmable Gate Array), 15-8
Front and Back radio buttons, 2-16
Front Cover, 2-10
Frontside and Backside options
K Panel Resin, 6-68, 6-69, 6-70
Overlay / Print Area, 6-46
Full bleed, 15-8
Full Card option, 6-49, 6-72
G
Gamma, 15-8
Glossy / Matte, 15-8
Glossy PVC, 15-8
Graphical Device Interface (GDI), 15-8
Gray Scale, 15-8
H
Halftoning, 15-8
Hard Drive, 15-9
hard Drive space
adequate or inadequate, 4-4
HDP (High Definition Printing™), 15-9
Head, 15-9
Headlift Motors, 4-32
Headlift Sensors, 4-32
Heat Seal, 15-9
Heat sink, 15-9
HiCo (High Coercivity), 15-9
high-resolution, 24-bit color images, 4-52
Horizontal adjustment, 6-27
HTML (HyperText Markup Language), 15-9
HTTP (HyperText Transfer Protocol), 15-9
Humidity, 2-4
I
IC (Integrated Circuit), 15-9
ID (Identification), 15-9
ID format, 6-15
Identification Card sample, 6-76
IEEE 1284 (Institute of Electrical and Electronics
Engineers 1284), 15-10
Image, 15-10
Image Color tab, 6-13, 6-21
Image Darkness option, 6-87
Image Placement, 4-50, 4-51
Image Placement option, 6-88
image placement problems, 4-50
Image Placement value, 6-88
Image Position controls, 6-26