Insignia NS-R27TR - Manual (Page 10)

10
Insignia NS-R27TR 27" Round Tube TV/DVD/VCR Combo
www.insignia-products.com
Connecting a digital audio device
Use the following illustration to connect a digital
audio device.
Using the TV
Watching TV
To watch TV:
1 Connect your antenna, cable TV, or satellite
receiver.
2 Plug your TV combo power plug into a power
outlet.
3 Press the POWER button to turn on your
TV combo.
4 Press the CH or CH button or use the
number buttons to select a channel.
5 Press the VOL. or VOL. button to adjust
the volume. Press the MUTE button to mute
or un-mute the sound.
Changing channels
To select a memorized channel:
•
Press the CH or CH button.
Or
• Press the appropriate number buttons. If you
are selecting a channel number larger than
100, press the +10/+100 button, then press
the number buttons for the two lower digits of
the channel button. For example, if you want
to select channel 120, press the +10/+100
button, press 2, then press 0.
Major and minor channels in digital TV (DTV)
A digital TV (DTV) channel has a main (major)
channel and may have one or more
sub-channels (minor channels).
When you use the CH
or CH buttons to
select a channel, the major channel is tuned first
followed by the minor channels.
To select a minor channel with the number
buttons:
•
Press the number buttons for the major
channel, then press the number buttons for
the minor channel. For example, if the major
channel is 12 and the minor channel is 3,
press 1, then 2, then 0, then 3. (You must
press the 0 if you are selecting a single-digit
minor channel number.
To search for a minor channel for the major
channel your are currently watching:
•
Press the +10/+100 button.
If the major channel has a one-digit channel
number, press the number button for the
major channel, press the ENTER button,
then press the number button for the minor
channel.
If the major channel has a two-digit channel
number, press the number buttons for the
major channel, then press the number button
for the minor channel. If you press the
ENTER button after you enter the two-digit
major channel number, your TV combo tunes
to the smallest minor channel number.
Switching modes
To switch modes:
•
Press the INPUT button one or more times to
select the TV/VCR or DVD mode. The
corresponding indicator light turns on the
front of your TV combo. For the location of
the indicator lights, see “Front control panel”
on page 6.
Adjusting picture settings
To adjust picture settings:
1 Press the PICTURE button.
2 Within five seconds, press the PICTURE
button to select the setting you want to
adjust. You can select:
• BRIGHT–Increases or decreases the
brightness.
• CONTRAST–Increases or decreases the
contrast.
• COLOR–Sharpens or softens the color.
• TINT–Adjusts the tint from purple to
green.
• SHARPNESS–Increases or decreases
the sharpness.
3 Press the or button to adjust the setting.
Note
Unless noted, all buttons in the following
instructions are remote control buttons.
Note
The first time you connect your TV combo to an
antenna or cable TV, it automatically scans for
and memorizes available channels.
Note
If you are using a cable converter box or satellite
receiver, set your TV combo to channel 3, 4, or
AUX, then use your cable converter box or
satellite receiver to change channels.
AUDIO OUT
COAXIAL
MD deck, DAT deck
Dolby Digital
decoder
AUDIO OUT COAXIAL
jack (DVD/DTV AUDIO
OUT) Coaxial digital
audio input jack on
external device
Back of TV combo
Cables not included
Note
TV/VCR mode includes analog TV, DTV, or AUX
mode. To use the VCR, select the TV/VCR mode.
Note
Your TV combo saves this setting even if you turn
off your TV combo or disconnect the power.
NS-R27TR.fm Page 10 Thursday, March 29, 2007 11:41 AM